Updated on November 17, 2026
This article contains affiliate links: if you buy through them, Wanda-techs earns a commission at no extra cost to you.
A Samsung TV problem comes in many forms: black screen, HDMI no signal, no Wi-Fi, a remote that does nothing, or a TV that switches itself on and off. Before you call support, a few checks at home narrow down the cause: source, cable, software, network, remote or power.
Common symptoms and causes
- Black screen but the sound works: wrong input, faulty cable, connected device switched off, or a backlight or power fault.
- No sound from a Samsung TV with an HDMI soundbar: HDMI ARC or eARC setting, audio output, Anynet+ (based on a Samsung help page we could not read in full).
- Samsung TV not connecting to Wi-Fi: weak signal, wrong password, router, or a 2018 model limited to 2.4 GHz.
- Samsung remote not working: batteries, infrared emitter, SolarCell charge, lost pairing.
- Samsung TV HDMI no signal: cable, port, selected input or connected device.
- Samsung TV turning on and off by itself: Anynet+ (HDMI-CEC), the Power On with Mobile feature (switching on from your smartphone), power supply.
Before you start
- Menus change with the model year: Device Care from 2022, Support > Self Diagnosis before 2019, Connection > Network on recent models and General > Network on older ones.
- Keep the TV’s PIN code at hand (for the reset) and your Wi-Fi password (after a network reset).
Warning: unplug the device from the mains before opening it, and never work on a device that is plugged in. The capacitors in some appliances (TVs, microwaves, power supplies) stay charged after unplugging, so do not touch them; opening the TV or its power board is a job for an authorized repairer. Unplug the TV before checking cables, too.
Warning: a factory reset and a network reset both erase data, so back up first. The first removes settings, Samsung accounts and installed apps; the second removes saved Wi-Fi networks.
Warning: opening the device may void the warranty, so check the warranty end date first. Out of warranty, repairs go through an authorized service center.
Solution 1: cold restart your Samsung TV
- Turn the TV on, point the remote at the screen and hold the Power button for about 5 seconds, until the TV switches off and back on.
- If the problem returns, turn the TV off and unplug it from the wall outlet.
- Wait 30 seconds, then plug it back in.
- Turn the TV on with the remote.
- Let the router and connected devices finish restarting before you test again.
Expected result: the TV restarts; check whether the problem is gone.

Solution 2: update the TV software
Warning: after an update, some settings may go back to their default values.
- Open Settings > All Settings > Support > Software Update.
- Select Update Now.
- If a USB drive is plugged in and the TV mentions it, choose No to update over Wi-Fi.
- Leave the TV on until the update finishes, and do not unplug it.
- Then hold the Power button until the TV switches off and back on.
Expected result: the TV restarts with the latest version of its software.
Tip: with no Internet connection, download the firmware (the TV’s internal software) from Samsung’s website and copy it to a USB drive that holds no other files.
Solution 3: black screen or HDMI no signal
- Press Home (or Menu) on the remote.
If the menu appears, the TV works and the problem lies with the input or the signal. If nothing appears, the power supply may be at fault: see our guide Samsung TV won’t turn on: what the indicator light means.
- Select the input that matches the port in use: HDMI 1 if the device is plugged into HDMI 1.
- Check that the connected device is switched on.
- Unplug and replug each cable at both ends.
- Replace any damaged cable.
- Turn the connected device off and on again.
- Plug the cable into a different HDMI port on the TV.
- Try another device or another cable to isolate the faulty part.
- Run the HDMI cable test in Settings > Support > Device Care > Self Diagnosis (HDMI Troubleshooting, 2022 models and later) or, on older models, in Settings > Support > Device Care > Self Diagnosis > Signal Information (HDMI Cable Test). The name of the test varies by model.
- Run the picture test: Settings > Support > Device Care > Self Diagnosis > Picture Test (on older models, Settings > Support > Self Diagnosis > Picture Test).
- Watch the test image, shown for about 5 seconds, then answer Yes, No or ask to see it again.
Expected result: a cable flagged by the HDMI test just needs replacing, no repair. A clean test image points to the cable or the connected device; lines or flickering point to a fault in the TV, which Samsung service should handle.
Good to know: the HDMI cable test targets cables shorter than 2 meters (about 6.5 feet), on some models only.
If the test points to the cable, here is one to replace it.

Belkin Ultra High Speed HDMI 2.1 cable, 2 m
Carries 4K and 8K picture and sound between a box, console or soundbar and the TV. A worn or bent cable can cause a black screen.
- AmazonSee at Amazon
With a One Connect box, unplug the TV from the mains before touching the box or its cable. A bent or pinched One Connect cable needs replacing. If a message or picture appears once the box is disconnected, the box itself is faulty.
If the screen flickers, turn off power saving (General menu, Eco Solution on 2021 models). On 2018 QLED models running software version 1270.6, also turn off LED Clear Motion (Picture > Expert Settings > Auto Motion Plus Settings) until an update is released. Menu names may vary.
Solution 4: Samsung TV not connecting to Wi-Fi
- Open Settings > All Settings > Connection > Network > Network Status, run the test and note the error message.
- Open Open Network Settings > Wireless and choose your network; for a hidden network, pick the add-network option at the bottom of the list (Add Network).
- Show the password as you type it and watch upper and lower case.
- Connect the TV to your smartphone’s hotspot.
If the TV connects to the phone, the fault lies with your router or Internet provider.
- Unplug the router, the modem and the TV.
- Plug them back in starting from the wall: modem first, then router, then TV, waiting for each one to start up.
- Open Network Status > IP Settings, set DNS to manual entry and enter
8.8.8.8(DNS Setting > Enter Manually > DNS Server).
The next step erases saved Wi-Fi networks, so keep your router’s password handy.
- Select Settings > Connection > Network > Reset Network, then reconnect the TV to your Wi-Fi.
Expected result: the Network Status test no longer reports an error.
Good to know: 2018 models in the NU6 and NU71 to NU73 series only pick up 2.4 GHz. If the signal is weak, move the TV closer to the router or add a range extender. A MAC address error calls for a factory reset, which erases settings, Samsung accounts and installed apps, and then Samsung service if the error returns.
If the signal stays weak, here is a Wi-Fi range extender.

TP-Link RE315 AC1200 dual-band Wi-Fi repeater
Extends the Wi-Fi signal into a room the router reaches poorly. Dual-band, it works on 2.4 GHz and 5 GHz.
- AmazonSee at Amazon
Solution 5: Samsung remote not working
- Put fresh AAA batteries in a standard remote.
- Check the infrared output: point the remote at a smartphone camera, press a button and watch the phone screen.
- Clear any obstacles between the remote and the TV.
- Recharge a SolarCell remote through its USB-C port: the red light stays on while it charges.
- Restart the remote: hold Back and Enter for more than 10 seconds on a SolarCell, or remove and reinsert the batteries of a standard remote.
- If it still does not respond, reset the SolarCell by holding Back and Mic for more than 3 seconds, until the MIC light goes out.
- Re-pair it: with the TV on and the remote within 6 meters (about 20 feet), point it at the TV and hold Back and Play/Pause for at least 3 seconds, then follow the on-screen instructions.
- If the fault lies with the TV, unplug it for 1 minute.
Expected result: the TV responds to button presses again.
For a standard remote, here are fresh AAA batteries.

Duracell Plus AAA (LR03) alkaline batteries, pack of 24
1.5 V alkaline AAA batteries for remote controls, thermostats and other low-drain devices. The large pack covers several changes.
- AmazonSee at Amazon

Meanwhile, control the TV with its control button (on the front, back or underside of the screen) or with the SmartThings app on compatible models; see our guide SmartThings won’t turn on your Samsung TV. The SolarCell charge level appears in Settings > All Settings > General & Privacy > Remote.
If nothing works
Stop and contact Samsung if you see lines on the picture test, no menu when you press Home, a blinking red light or no power at all, a MAC address error after a reset, or HDMI ports that stay silent with a cable and a device that work elsewhere.
If the TV has Internet access, open Settings > Support > Remote Management for Samsung’s remote assistance. In the United States, Samsung support answers on 1-800-SAMSUNG (1-800-726-7864); repairs go through a Samsung service center or an authorized repairer.
Tip: before you call, note the model and serial number, the software version, the purchase date and any error message you saw.
Take better care of your Samsung TV: our toolbox
A few accessories useful to Samsung TV owners: remote, HDMI ARC sound, cables.
- One For All Contour 4 universal remote (URC 1240)Remote that controls up to four devices: TV, set-top box, player and soundbar. It replaces a lost or broken remote.AmazonSee at Amazon
- Belkin Ultra High Speed HDMI 2.1 cable, 2 mCarries 4K and 8K picture and sound between a box, console or soundbar and the TV. A worn or bent cable can cause a black screen.AmazonSee at Amazon
- LG SP2 2.1 soundbar, 100 W, HDMI ARC and BluetoothImproves TV sound with a built-in subwoofer. It connects through HDMI ARC and also accepts Bluetooth.AmazonSee at Amazon
- UGREEN Cat 6 Ethernet cable, 5 mConnects a PC straight to the router for a stable wired connection. Handy for testing the network or working while Wi-Fi is down.AmazonSee at Amazon
Frequently asked questions
How do I reset a Samsung TV?
On a 2019 or newer model, the reset, which erases settings, Samsung accounts and installed apps, is in Home > Settings > General & Privacy > Reset: enter the PIN, confirm with Yes, then set the TV up again. The default PIN is 1111 according to Samsung’s French page and 0000 according to other Samsung pages. Before 2019, the command is in Settings > Support > Self Diagnosis > Reset.
Why does my Samsung TV have sound but no picture?
A wrong input, a faulty cable, a connected device switched off, or a backlight or power fault can all cause it. Press Home: if the menu appears, the TV works and Solution 3 applies. If the screen stays black, contact Samsung service.
Why does my Samsung TV turn on and off by itself?
Anynet+ (HDMI-CEC, which lets devices control each other over the HDMI cable), the Power On with Mobile feature or the power supply can be the cause. Unplug the TV for 30 seconds, check the power cord, plug it straight into the wall without a surge protector and update the software. Then turn off Anynet+ (External Device Manager) and Power On with Mobile (General > Network > Expert Settings), at the cost of switching on from SmartThings; if it keeps happening, contact Samsung.
How do I run a self-diagnosis on a Samsung TV?
Open Settings > Support > Device Care > Self Diagnosis on a recent model, or Settings > Support > Self Diagnosis on an older one. Lines or flickering on the Picture Test point to a fault in the TV; the HDMI cable test checks the cable on compatible models.
Share this content:
