This article contains affiliate links: if you buy through them, Wanda-techs earns a commission at no extra cost to you.
To open a phone, a console or a laptop, an iFixit toolkit gives you the 4 mm bits and the opening tools: the Pro Tech Toolkit has 64 bits, the Essential Electronics Toolkit 16. To measure, our pick is the UNI-T UT61E+ with its 22,000 counts on the bench, or the Fluke 117 if you also check voltages on a building’s wiring. To resolder, the Pinecil V2 is an iron powered over USB-C, as long as you give it a charger strong enough.
Our picks at a glance
- iFixit Pro Tech Toolkit: our pick for repairing almost anything, 64 bits, opening tools and an anti-static wrist strap.
- iFixit Essential Electronics Toolkit: for a few repairs a year, 16 bits and the basic opening tools.
- UNI-T UT61E+: our pick for bench electronics, True RMS, 22,000 counts and a USB link.
- Fluke 117: for anyone who also measures mains power, CAT III 600 V, non-contact detection and a 3-year warranty.
- Pinecil V2: for soldering, an iron powered by USB-C PD or a barrel jack, up to 88 W at 24 V.

How to choose your iFixit toolkit, multimeter and soldering iron
A repair bench comes down to three gestures: open, measure, resolder.
iFixit Pro Tech Toolkit or Essential: the bits
Count the types of bits rather than their total number. The Pro Tech Toolkit adds JIS bits, nut drivers and gamebit bits, for example, none of which the Essential has. If you only repair a phone now and then, the small kit is enough.
Multimeter: CAT rating and True RMS
The CAT rating tells you which surges the meter can withstand, depending on where in the electrical system you measure. It matters as soon as you get near mains power: the Fluke 117 is rated CAT III 600 V and withstands a 6 kV surge. True RMS means the meter reads the real effective value of an AC voltage, even when the signal is not a clean sine wave; the Fluke 117 and the UNI-T UT61E+ both do.
The number of counts is the resolution of the display. The UT61E+ shows 22,000 counts, the Fluke 117 6,000 counts.
Powering the soldering iron
A USB-C iron depends on its charger. The Pinecil V2 accepts USB-C Power Delivery (PD) or Quick Charge 3.0 from 12 to 20 V at 3 A, or a DC5525 barrel jack from 12 to 24 V at 3 A minimum. A 12 V charger makes it heat up more slowly than a 20 V / 3 A PD charger.
Anti-static protection
An anti-static wrist strap connects your wrist to ground to drain static electricity. In the Pro Tech Toolkit, only the wrist strap is presented as anti-static; iFixit does not say the case, the foam or the tools are. The Essential has no anti-static item, and iFixit sells these accessories separately.
Before you start
These tools are for working on electrical devices and batteries. Read these safety notes before your first teardown.
Warning: unplug the device from the mains before opening it; never work on a device that is plugged in; the capacitors in some devices (TVs, microwave ovens, power supplies) stay charged after unplugging, so do not touch them.
Warning: never measure mains power with a multimeter whose CAT rating is not suitable, or with test leads that have no protective shrouds. Check the meter’s fuses, and never measure a voltage with the leads plugged into the current (amps) jack.
Warning: never puncture, bend or heat a lithium battery; a swollen battery must not be recharged and goes to a collection point; work on a non-flammable surface. Do not pry under a battery with a metal spudger.
Warning: the tip of a soldering iron burns as soon as it is on. Always rest it on its stand and ventilate the room so you do not breathe in solder fumes.
Warning: opening a device can void its warranty; check the warranty end date first. Soldering on the board has the same effect.
iFixit Pro Tech Toolkit: for repairing almost anything
Here are the current offers for the Pro Tech Toolkit.

iFixit Pro Tech Toolkit, 64-bit repair kit
Brings together 64 precision 4 mm bits, opening tools, tweezers, a suction handle and an anti-static wrist strap. Everything needed to open and repair phones, consoles and laptops.
- AmazonSee at Amazon
The Pro Tech Toolkit (part number IF145-307-4) holds 64 4 mm bits in S2 steel. You get Hex, Phillips, Torx, Torx Security, Tri-point, Pentalobe, slotted, JIS, square, gamebit, triangle and spanner bits, plus six nut drivers. It also comes with a 1/4″ to 4 mm adapter, a bit for iPhone standoffs, a magnetic screw pickup and a SIM card eject tool.
For opening devices, the kit provides an anodized aluminum driver, a flexible extension, a jimmy (a thin blade for prying cases apart), a pick and an opening tool, three spudgers (levers for unclipping, one of them metal), three tweezers and a suction cup. The anti-static wrist strap is included. Everything is stored in an ABS case with a magnetic lid and an EVA foam insert, measuring 8.25 x 5.6 x 2.75 inches; the lid doubles as a parts tray.
Its limits: the wrist strap is the only item advertised as anti-static. If you only have one phone to open, a good share of the bits will go unused.
iFixit Essential Electronics Toolkit: for a few repairs a year
Here are the current offers for the Essential Electronics Toolkit.

iFixit Essential Electronics Toolkit, 16-bit repair kit
A magnetic driver, 16 bits of 4 mm and the basic opening tools in a compact case. Enough to replace a battery or a screen from time to time.
- AmazonSee at Amazon
The Essential Electronics Toolkit has 16 bits and a SIM card eject cap: 5 Phillips, 3 slotted, 3 Torx Security, 2 Torx, 2 Pentalobe and 1 Tri-point. Its polymer driver has a 4 mm magnetic bit holder. It adds angled tweezers, a spudger, a jimmy and opening picks, in a magnetized ABS box with EVA foam whose lid serves as a tray.
iFixit covers it with its Lifetime Guarantee and its Quality Guarantee. Its limits: no JIS bit, no nut drivers, no suction cup and no anti-static wrist strap. It is the kit for someone who swaps a battery or a screen from time to time.
UNI-T UT61E+: for bench electronics
Here are the current offers for the UNI-T UT61E+.

UNI-T UT61E+ True RMS multimeter, 22,000 counts
A True RMS digital multimeter with 22,000 counts, backlight, data hold and a USB cable to log readings on a computer. A precise meter for voltages, resistances and components on the bench.
- AmazonSee at Amazon
The UT61E+ is a True RMS multimeter with 22,000 counts and, according to UNI-T’s page, a maximum input voltage of 1,000 V AC and DC. It holds the reading on screen (data hold), records min, max and relative values, and has a backlight and a 46-segment bargraph. It adds non-contact voltage detection with an alarm (NCV), LPF and LoZ modes for AC voltage, transistor hFE measurement, peak hold, diode and continuity tests.

It comes with gold-plated test leads and a USB cable to log readings on a computer. Its limit: Bluetooth and the app are optional. The UNI-T page we read does not state its CAT rating.
Warning: do not use the UT61E+ on mains power until you have checked its CAT rating on the meter and in its manual.
Fluke 117: for measuring mains power too
Here are the current offers for the Fluke 117.

Fluke 117 True RMS multimeter with non-contact voltage detection
A True RMS electrician multimeter rated CAT III 600 V, with VoltAlert non-contact voltage detection and a low-impedance mode against ghost voltages. Fluke covers it with a 3-year warranty.
- AmazonSee at Amazon
The Fluke 117 is rated CAT III 600 V, with 600 V at most to ground and a 6 kV surge withstand. It is True RMS for AC voltage and current, shows 6,000 counts, a 33-segment bargraph and a white LED backlight. Its VoltAlert function detects voltage without contact, LoZ mode rules out ghost voltages and AutoVolt picks AC or DC on its own.
It measures DC voltage from 600 mV to 600 V with an accuracy of 0.5% + 2, current up to 10 A (20 A for 30 seconds) and resistance up to 40 MΩ. It also measures capacitance and frequency, tests continuity and diodes, and keeps Min/Max/Average values. Fluke guarantees it for 3 years; it runs on a 9 V alkaline battery for about 400 hours.
Its current input is protected by an 11 A 1,000 V fast-blow fuse.
Its limits: 6,000 counts is less fine than the 22,000 of the UT61E+, and it weighs 550 g for 167 x 84 x 46 mm. Fluke designs it for electricians. It costs noticeably more than an entry-level multimeter, which is hard to justify for occasional use.
Pinecil V2: for resoldering a connector or a wire
Here are the current offers for the Pinecil V2; check whether a charger is included.

Pinecil V2 soldering iron, USB-C PD and DC5525 barrel
A compact soldering iron running the open-source IronOS firmware, powered by a USB-C Power Delivery charger or a 12 to 24 V DC5525 barrel jack. It heats faster on a USB-C PD 20 V / 3 A charger than on a 12 V one.
- AmazonSee at Amazon
The Pinecil V2 came out in August 2022 and runs the open-source IronOS firmware. Its official power is 88 W at 24 V. It is powered by USB-C PD or QC 3.0 from 12 to 20 V at 3 A, or by a DC5525 barrel jack from 12 to 24 V at 3 A minimum, one port at a time.
Its limits come from the power supply. With a 12 V charger, it heats up more slowly than with a 20 V / 3 A PD charger. According to PINE64, 28 V / 140 W EPR chargers are tolerated but, for the most part, untested.
Tip: for faster heating, plug it into a 20 V / 3 A USB-C PD charger rather than a 12 V one.
Good to know: on the page of the first Pinecil, PINE64 states that a B2 tip is fitted by default, that extra tips are sold separately, and recommends its PinePower supply. Check the offer to see whether a charger is included before you order.

Comparison table
| Tool | Key features | Who it is for |
|---|---|---|
| iFixit Pro Tech Toolkit | 64 4 mm bits, opening tools, anti-static wrist strap | Frequent repairs, all devices |
| iFixit Essential Electronics Toolkit | 16 4 mm bits, basic opening tools | Occasional repairs |
| UNI-T UT61E+ | True RMS, 22,000 counts, 1,000 V max, USB | Bench electronics |
| Fluke 117 | True RMS, 6,000 counts, CAT III 600 V, VoltAlert, 3-year warranty | Mains measurements |
| Pinecil V2 | 88 W at 24 V, USB-C PD 12-20 V or barrel jack 12-24 V | Soldering connectors and wires |
To compare the offers for the five tools side by side, here is our selection.
- iFixit Pro Tech Toolkit, 64-bit repair kitBrings together 64 precision 4 mm bits, opening tools, tweezers, a suction handle and an anti-static wrist strap. Everything needed to open and repair phones, consoles and laptops.AmazonSee at Amazon
- iFixit Essential Electronics Toolkit, 16-bit repair kitA magnetic driver, 16 bits of 4 mm and the basic opening tools in a compact case. Enough to replace a battery or a screen from time to time.AmazonSee at Amazon
- UNI-T UT61E+ True RMS multimeter, 22,000 countsA True RMS digital multimeter with 22,000 counts, backlight, data hold and a USB cable to log readings on a computer. A precise meter for voltages, resistances and components on the bench.AmazonSee at Amazon
- Fluke 117 True RMS multimeter with non-contact voltage detectionA True RMS electrician multimeter rated CAT III 600 V, with VoltAlert non-contact voltage detection and a low-impedance mode against ghost voltages. Fluke covers it with a 3-year warranty.AmazonSee at Amazon
- Pinecil V2 soldering iron, USB-C PD and DC5525 barrelA compact soldering iron running the open-source IronOS firmware, powered by a USB-C Power Delivery charger or a 12 to 24 V DC5525 barrel jack. It heats faster on a USB-C PD 20 V / 3 A charger than on a 12 V one.AmazonSee at Amazon
Buying at the right time
Black Friday falls on Friday, November 27, 2026 and Cyber Monday on Monday, November 30, 2026. Our page on the real tech deals of Black Friday 2026 tracks the categories to watch. Before you confirm a cart of tools, run through these checks.
- Note the exact name of the kit: the Pro Tech Toolkit (64 bits) and the Essential Electronics Toolkit (16 bits) do not contain the same tools.
- For a multimeter, compare the CAT rating in the listing with the manufacturer’s: CAT III 600 V for the Fluke 117.
- For the Pinecil, check that it is the V2 and plan for a 20 V / 3 A USB-C PD charger if the offer does not include one.
- Compare the crossed-out price with the lowest price the seller charged during the 30 days before the discount.
In France, a discount announcement must show this lowest price of the last 30 days as its reference price; when prices drop several times in a row, the reference stays the price before the first drop. In other countries the rule differs, so check your own market’s pricing rules. To spot an inflated crossed-out price, follow our method for checking a fake Black Friday deal.
Complete your repair bench: our toolbox
These accessories protect the components, power the iron and make taking devices apart safer.
- iFixit portable anti-static mat with wrist strapA foldable grounded mat supplied with a wrist strap and a grounding cord. It drains static electricity while you handle boards and components.AmazonSee at Amazon
UGREEN Nexode 65 W charger (3 ports)One wall charger for a laptop, a phone and a third device at once.AmazonSee at Amazon- MG Chemicals 8341 no-clean flux paste, 10 ml syringeA no-clean flux paste in a syringe, for touch-ups and surface-mount soldering. It helps solder wet pads and wires properly.AmazonSee at Amazon
- iFixit FixMat, magnetic repair mat with compartmentsA magnetic work mat with compartments to sort screws and small parts as you take a device apart. You reassemble it without losing or mixing up screws.AmazonSee at Amazon
Frequently asked questions
Which iFixit toolkit should I choose?
Choose the Pro Tech Toolkit if you repair often or work on a variety of devices: 64 bits, a full set of opening tools and an anti-static wrist strap. The Essential Electronics Toolkit, with 16 bits, is enough for swapping a battery or a screen from time to time. It has no JIS bit, no nut drivers and no anti-static wrist strap.
Which multimeter should I buy to start in electronics?
For bench electronics, our pick is the UNI-T UT61E+: True RMS, 22,000 counts, diode and continuity tests. Its USB link lets you log readings on a computer. Its CAT rating is not stated on UNI-T’s page: for mains power, choose the Fluke 117, rated CAT III 600 V.
Which soldering iron should I use to repair electronics?
The Pinecil V2 is our pick for resoldering a connector or a wire: 88 W at 24 V, powered by USB-C PD or a barrel jack. Plan for a 20 V / 3 A USB-C PD charger, because a 12 V charger makes it heat up more slowly.
What tools do I need to open a smartphone or a laptop?
You need a driver with the right bits, for example Pentalobe, Tri-point, Torx or Phillips, and tools to pry the case apart: jimmy, picks, spudger and suction cup. The Pro Tech Toolkit has all of that, with an anti-static wrist strap. The Essential Electronics Toolkit also has Pentalobe, Tri-point, Torx and Phillips bits, but no suction cup.
Photo credits: electronics-workbench by geekabit, licence CC0 1.0; Macro shot of screwdriver bits by Don DeBold from San Jose, CA, USA, licence CC BY 2.0; Digital Multimeter by oomlout, licence CC BY-SA 2.0; Soldering iron in holder by Bgrimer, licence CC BY-SA 3.0
Share this content:
