This article contains affiliate links: if you buy through them, Wanda-techs earns a commission at no extra cost to you.
Your rear window defroster is not working: the indicator light stays off, nothing heats up, or only a few lines clear. Before you hunt for a fault, check that the function has not simply switched itself off. Then move on to the fuse, the grid lines and the terminals on the glass.
Common symptoms and causes
- Nothing defrosts: fuse, relay, switch or wiring harness.
- Only a few lines heat: a broken grid line or a faulty side terminal.
- The indicator light goes out: normal automatic shut-off, a fuse or the wiring.
- The function stops after a delay: that is by design, and the length varies with the make and model.
- Nothing happens with the engine off: in the manuals we read, the function needs the engine running.
Before you start
Keep your vehicle’s owner’s manual at hand: it gives the location and amperage rating of the fuse. For solution 3 you will also need a multimeter, the tool that measures voltage and continuity. The grid lines are the thin heating lines printed on the inside face of the rear window.
Warning: switch off the ignition; do not touch the airbags, the seat belt pretensioners or the high-voltage system of a hybrid or electric vehicle; a red warning light means you must stop the vehicle; this procedure does not replace a diagnosis in a workshop. Restart the engine only for the tests that call for it.
On the 12 V circuit, always replace a fuse with one of the amperage rating given in the owner’s manual, never a higher one. Do not clean the inside of the rear window with a sharp object or an abrasive product: you would cut the grid lines.
Warning: opening the device can void the warranty, so check when your warranty ends first. If the car is still under warranty, have a workshop repair the grid line or the tailgate wiring.
Tip: in heavy snow, brush the rear window first before turning on the defroster, as Kia recommends.
Solution 1: check the indicator light and the automatic shut-off
- Start the engine: the Kia, Dacia, Peugeot and Mazda manuals we read call for the engine running or the ignition on.
- Press the rear window defroster button once.
- Look at the indicator light on the button: it stays lit as long as the function is active.
- Let the function run without pressing again, because a second press switches it off.

The glass should clear gradually, with the light on. The light goes out by itself when the timer runs out, and that is normal.
On a Kia, the defroster stops after about 20 minutes or when you switch the ignition off. On a Mazda, it stops after about 15 minutes at higher temperatures; in cold weather it keeps running until you press the button again. Peugeot ties the duration to the outside temperature, and Dacia leaves it to the system.
Good to know: on the Peugeot 3008 and 5008, the car cuts some electrical functions to save the battery, according to the energy left in it. While you drive, it can switch off the air conditioning and the rear window defroster for a while, then turns them back on by itself as soon as conditions allow. Peugeot also states that the function shuts itself off to avoid drawing too much current.
Depending on the version, the same button also heats the outside mirrors (Peugeot, Dacia). According to an unofficial specialist site, the symbol is a rectangle with upward arrows, in orange or yellow.
Solution 2: check the rear defroster fuse
According to specialist sites, an indicator light that does not come on can point to a blown fuse or a severed wiring harness. With the ignition off, check the dedicated fuse.
Warning: for the 3008 and 5008, Peugeot says that having a third party replace a fuse can cause a serious malfunction, and asks you to go through its network or a qualified workshop. On those models, stop at step 3.
- Open your owner’s manual at the fuse diagram.
- Find the rear window defroster line in the fuse assignment table (the wording differs from one manual to another).
- Note the location and the amperage rating the manual gives for that fuse.
- Find that fuse in the fuse box using the manual’s diagram and check its condition.
- Replace a blown fuse with one of the amperage rating given in the manual, never a higher one.
After the replacement, the indicator light should come on when you press the button with the engine running.
Tip: do not trust an amperage rating you read on a forum; only the owner’s manual is authoritative.
To keep spare fuses and a tester at hand, here is an assortment to choose from according to the rating in your manual.

Assortment of 306 car fuses, standard and mini blade, with puller and tester
A box of standard and mini blade fuses in the common ratings, with a puller and a tester to check them. Handy to keep in the glovebox.
- AmazonSee at Amazon
Our guide on a cigarette lighter that stopped working follows the same method for checking fuses.
Solution 3: find and repair a broken grid line
If only some of the lines on the glass clear, a grid line is broken or a terminal is at fault. According to an auto parts specialist site, a multimeter reading helps tell the two apart.
- Turn on the defroster with the engine running.
- Measure the voltage across the rear window’s terminals with the multimeter: the expected value is about
12 V. - If you read
0 V, look at the supply side (switch, fuse, wiring) rather than at the grid line.
The same site notes that a broken grid can mimic a relay fault.
Good to know: the repair can be done without removing anything, using a conductive paint kit. The steps below follow the instructions of the Permatex Quick Grid kit; for another kit, follow its own instructions.
If you would rather do the repair yourself, here is a complete defroster repair kit with stencil, conductive paint and wipes.

Permatex 09117: complete rear window defogger repair kit
Restores a broken heating line without removing the glass, with stencil, conductive paint and wipes. The kit also includes adhesive to re-fix a loose terminal.
- AmazonSee at Amazon
- Find the broken line, by eye or with the multimeter.
- Turn the defroster off.
- Clean the area to repair with the kit’s alcohol wipe.
- Place the stencil aligned with both ends of the line, pressed flat against the glass with no bubbles.
- Shake the bottle.
- With the brush, cover both ends of the break.
- Apply three coats, letting each one become tack-free before the next.
- Look at the repair from inside the car: if light still shows through, add another coat.
- Remove the stencil after 30 minutes.
- Wait 24 hours before turning the defroster back on.

The repaired line should defrost like its neighbors again. Work preferably between 10 and 24 °C (50 to 75 °F), the ideal range given by the manufacturer. With a multimeter, you can check for 0 ohm of continuity on either side of the repair; the bottle carries a safety warning to read before use.
Solution 4: check the terminals on the sides of the rear window
The terminals are the connectors fixed on the sides of the glass that feed power to it. According to user reports and a specialist blog, with no manufacturer source, they can oxidize or work loose over time.
- Look at the terminals on each side of the rear window: check for oxidation, or a terminal that is loose or has come unstuck.
- If a terminal is damaged or no longer holds, leave the repair to a workshop.
You now know whether the terminals are the cause. Repairing them is a workshop job.
If nothing works
Stop and go to a garage in these cases: the fuse is fine but there is no voltage across the rear window’s terminals, the relay is built into an electronic unit, the tailgate wiring is at fault, or several grid lines are broken or terminals have come unstuck.
According to a specialist site, with the ignition on, pressing the button should produce the click of the relay; with no click, the relay, the switch or the wiring is suspect. On some models, the relay is built into the UCH (the passenger compartment’s electronic control unit): it cannot be replaced on its own and needs a professional diagnosis.
Have the owner’s manual at hand, along with a list of what you have already checked: fuse, measured voltage, lines that heat or not. If the car is under warranty, leave the repair to a workshop.
While you wait for the repair, clear the rear window without scraping its inside face. Our guides on fog on the windshield and a windshield frozen on the inside cover methods that also work on the rear glass.
Take better care of your rear defogger: our toolbox
Everything to repair, check and keep your windows clear.
- Permatex 09117: complete rear window defogger repair kitRestores a broken heating line without removing the glass, with stencil, conductive paint and wipes. The kit also includes adhesive to re-fix a loose terminal.AmazonSee at Amazon
- Assortment of 306 car fuses, standard and mini blade, with puller and testerA box of standard and mini blade fuses in the common ratings, with a puller and a tester to check them. Handy to keep in the glovebox.AmazonSee at Amazon
- AstroAI digital multimeter, 2000 countsMeasures voltage, current and continuity on a car circuit. A simple way to tell a power fault from a broken part.AmazonSee at Amazon
- Sonax anti-fog spray, 300 mlLeaves an invisible film on glass that slows condensation from forming. Useful on windscreens, rear windows and mirrors.AmazonSee at Amazon
- Sonax microfibre cloth Plus for interior and glassA soft cloth that wipes the inside of glass without leaving lint or scratches. Good for clearing misted windows.AmazonSee at Amazon
Frequently asked questions
Why is my rear window defroster not working?
The function may have stopped normally: an automatic shut-off after a delay that varies with the model, the engine being off, or, on the Peugeot 3008 and 5008, the car cutting some electrical functions to save a low battery. If nothing heats, check the fuse, then the power supply, the relay, the switch and the wiring harness. If only a few lines defrost, a grid line is broken or, according to user reports, a side terminal is oxidized or loose.
Where is the rear defroster fuse?
Its location and amperage rating are in the fuse diagram of your vehicle’s owner’s manual, and they change from one model to the next. The Dacia Nouveau Duster manual, for example, lists a fuse for the heated rear window in its assignment table. Do not trust an amperage rating you read on a forum: only the owner’s manual is authoritative.
How do I repair a broken defroster grid line?
With a conductive paint repair kit, without removing anything. According to the instructions of the Permatex Quick Grid kit, you place a stencil over the broken line, apply three coats with the brush, remove the stencil after 30 minutes and wait 24 hours before turning the defroster back on. For another kit, follow its instructions.
Does the rear defroster switch off by itself?
Yes, on the models whose manuals we read, but the duration varies. Kia states about 20 minutes, Mazda about 15 minutes at higher temperatures, Peugeot a duration that depends on the outside temperature, and Dacia a duration set by the system. On a Mazda in cold weather, the function can stay on until you press the button again.
Share this content:
