When an oven stops heating, Bosch points to two technical causes: a faulty heating element or a failed heating system. Often, though, nothing is broken. A tripped breaker, an active child lock or a pyrolytic door lock can also stop the heat, and you can check all of them without tools.
Common symptoms and causes
Bosch lists an oven that stops heating among its technical problems. These are the symptoms and causes it reports:
- The oven heats too much, too little, or unevenly.
- The bottom heat (the lower element) does not work.
- A heating element is faulty, or the whole heating system is.
- The child lock is on: the oven will not start and shows
SAFE,LOC,LOCKor a padlock (Electrolux source). - The door stays locked after a pyrolytic (self-cleaning) cycle.
- A thermal safety has cut the heat: this lead comes from forums, with no official confirmation.
Before you start
Work on a cold oven. Note the exact model number on the rating plate: it gets you the right manual.
Warning: unplug the appliance from the mains before opening it; never work on a connected appliance; the capacitors in some appliances (TVs, microwaves, power supplies) stay charged after unplugging, so do not touch them.
Warning: opening the appliance may void the warranty; check when your warranty ends first.
This guide covers electric ovens only. For a gas oven, call a professional.
Solution 1: check the power supply to the oven
The circuit breaker is the protective switch for the oven in your fuse box. The residual-current device (RCD, or GFCI in the United States) cuts the power when current leaks. This common-sense check is not described in the official pages consulted.
- Check whether the display, the clock or the oven light comes on.
- Open the fuse box and find the oven’s breaker.
- If that breaker or the RCD has tripped, switch it back on.
- For a freestanding plug-in oven, plug another appliance into the same socket to check that it works.
- If there was a recent power cut, look at the display: the time may need to be set again (see Solution 2).
The oven should light up and respond to the buttons.
Warning: if the breaker trips again, leave it off and contact customer service or an electrician.
Solution 2: turn off the child lock and set the clock
According to Electrolux, the child lock stops the oven from starting and locks the door. This applies to built-in ovens and to ranges alike. The buttons to use vary by model.
- Look at the display:
SAFE,LOC,LOCKor a padlock symbol means the child lock is on. - Turn the function selector to OFF.
- Hold the button combination for your model for 2 seconds. The manual gives it in the “Additional functions” chapter.
On Electrolux models with a control knob, the lock is set in the menu.
- Open Menu > Basic settings > Child lock.
- Turn the function off.
- If the oven shows “Child lock” at start-up and asks for the code, use the knob to select the letters A, B and then C, in that order.
The padlock symbol should disappear and the oven should accept a cooking program.

On some models, according to user reports, an unset clock or a demo mode stops the oven from heating. No official page consulted confirms this.
- If the time is not set, set it by following your model’s manual.
- If the manual mentions a demo mode, follow its exit procedure.
The time should stay fixed on the display and the oven should heat when you start a cooking program.
Solution 3: oven not heating after a pyrolytic cycle, wait for the door to release
Pyrolysis is the oven’s automatic high-temperature cleaning. Electrolux notes that the locked-door symbol also appears during this cycle, without giving a cool-down time. Steps 2 and 3 come from user reports, not from an official page.
- Check whether the locked-door symbol is showing.
- Let the oven cool with the door closed, and do not force the handle.
- Wait until the lock symbol goes out and the door releases.
According to those same reports, the door releases once the inside drops below about 250 °C (480 °F). The door should then open. Then start a normal cooking program to check that the oven heats.
Good to know: forums mention a thermal safety, a fuse that cuts the heat if the oven overheats. A technician should test and replace it. Never bypass it by joining wires together.
Solution 4: oven not heating at the bottom or in fan mode
An electric oven has several elements: the bake element at the bottom, the broil element at the top, and often a circular element around the fan for fan-assisted (convection) heat. Testing the modes one by one shows which one no longer heats. This is diagnostic logic: no official manual consulted describes it.
- Start the bottom heat only mode at a medium temperature.
- After a few minutes, look through the glass with the door closed to see whether the top or bottom element glows red.
- Switch the oven off and let it cool a little.
- Repeat with the top heat only, then with fan mode.
- Note which modes stay cold.
You now know which element stays cold: bottom, top or circular. If the fan runs but the oven does not heat in fan mode, while the bottom and top heat fine, the circular element may be at fault.

Tip: keep the list of cold modes handy. The technician will ask for it, and it saves them from diagnosing blind.
Warning: do not open the oven or remove any element. Bosch lists a faulty heating element among the causes; replacing one is done with the oven unplugged, by a technician.
Solution 5: measure the real temperature with a thermometer
An oven that heats a little can still heat too little: Bosch lists “heats too little” among the symptoms. An oven thermometer, a dial placed on the rack, compares the real temperature with the set one. No manual consulted describes this test, so use the temperature from your manual or from a recipe you know well.
- Place an oven thermometer on the rack.
- Set the oven to the temperature given in your manual or recipe.
- Wait until preheating is finished.
- Read the temperature through the glass, without opening the door.
- Compare the reading with the set temperature.
The reading should stay close to the set temperature. If the gap is large and keeps coming back, customer service will check the thermostat and the temperature probe, among other parts.
Tip: do not read the thermometer with the door open. Each opening makes the temperature drop and skews the measurement.
If nothing works
Stop here if the power supply, the child lock, the clock and the pyrolytic lock are all ruled out. The element, the thermostat, the probe or the electronic board are a job for the manufacturer’s customer service or a technician.
At Bosch (France), customer service answers by email or phone Monday to Friday, 8:30 a.m. to 12 p.m. and 2 p.m. to 5:30 p.m. (French hours). Its repair page covers ovens under warranty and out of warranty, with genuine parts.
Have these ready:
- the model number, from the rating plate;
- the purchase date and the invoice, for the warranty;
- the error code on the display, if there is one;
- the modes that heat and the ones that stay cold (Solution 4).
The same approach works for other cooking appliances: see our guide on an induction hob that stops heating. For another failed heating element, also read the one on a tumble dryer that stops heating.
Frequently asked questions
Why does my oven turn on but not heat?
An active child lock or a faulty heating element are possible causes. Electrolux says that with the child lock on, the oven shows SAFE, LOC, LOCK or a padlock. If you see nothing of the kind, test each heating mode to find the element that stays cold.
Why did my oven stop heating after a power cut?
Check the oven’s breaker first, then the clock setting. According to user reports, some ovens refuse to heat until the clock is set. No official manual consulted confirms this: follow the one for your model.
Why is my oven not heating at the bottom?
The bake element, the one at the bottom, is a possible cause. Bosch lists bottom heat not working among the symptoms and a faulty heating element among the causes. Confirm it with the test in Solution 4, then call a technician.
When should you replace an oven’s heating element?
When one heating mode stays cold while the others heat, and the power supply and the safeties are ruled out. A technician tests the element before replacing it with a part matching the model number. Do not remove it yourself.
Share this content:
