Advertisement
Cars

Car heater not blowing hot air: what should you check first?

A car heater that blows cold air most often comes from a coolant level that is too low. Here are the checks to run in order, from the level to the thermostat.

6 min read

Stylized car with a snowflake, a drop of fluid and a repair wrench
Table of contents
  1. Common symptoms and causes
  2. Before you start
  3. Solution 1: check the coolant level
  4. Solution 2: no air at all, check the fuse and the blower motor
  5. Solution 3: bleed the air out of the cooling system
  6. Solution 4: temperature gauge stays low, check the thermostat
  7. Solution 5: clogged heater core or blend door
  8. If nothing works
  9. Get your car ready for winter: our toolbox
  10. Frequently asked questions
    1. Why is my car heater blowing cold air?
    2. Can low coolant stop the heater from working?
    3. Can a thermostat stuck open stop the heater?
    4. Why is the fan not blowing at all?

This article contains affiliate links: if you buy through them, Wanda-techs earns a commission at no extra cost to you.

When your car heater is not blowing hot air, the air stays cold even with a warm engine, or the fan stops blowing altogether. Most often the coolant level is too low, because of a leak, evaporation or skipped maintenance. Check that level first, then work through the solutions in order.

Advertisement

Common symptoms and causes

On a gasoline, diesel or hybrid car, the heater uses heat from the coolant, the fluid that carries heat away from the engine. The symptom points to the cause.

  • Cold air while the engine is warm: low coolant, an air bubble in the system, a clogged heater core, or a faulty heater valve or blend door.
  • Temperature gauge stays low: thermostat stuck open.
  • No air at all: fuse, blower motor (the fan that pushes air into the cabin) or blower resistor.
  • Air only on some fan speeds: blower resistor.

A sensor or the climate control electronics can also be at fault.

Before you start

This guide covers gasoline, diesel and hybrid cars. It does not cover heating in electric cars: on those models, leave the fault to a professional.

Have ready:

  • the owner’s manual, for the fuse location, the coolant type and the level marks;
  • a cold engine to check the level;
  • a multimeter for solution 2.

Warning: switch the ignition off; do not touch airbags, seat belt pretensioners or the high-voltage system of a hybrid or electric vehicle; a red warning light means stop the vehicle; this procedure does not replace a workshop diagnosis.

Warning: never open the coolant reservoir cap on a hot engine, the fluid is under pressure. With a hot engine, the radiator fan can start without warning: keep your hands and tools clear.

Advertisement

Do not put this fault off. Without heat, defogging works poorly and visibility drops.

A cooling fault can also lead to overheating and then to expensive engine damage. If the temperature gauge or warning light goes into the hot zone, pull over and stop driving.

Solution 1: check the coolant level

The coolant reservoir, also called the expansion tank, holds the engine coolant under the hood. Park the car and switch the ignition off.

  1. Wait until the engine is cold.
  2. Open the hood and find the coolant reservoir.
  3. Look up the level marks and the recommended coolant type in the owner’s manual.
  4. Check the fluid level in the reservoir.
  5. Top up to the MAX mark with the recommended type of coolant.
  6. Look for signs of a leak on the hoses, the radiator and the water pump.
chauffage-voiture-ne-chauffe-plus-1-1024x576 Car heater not blowing hot air: what should you check first?
Check the coolant level with the engine cold, at the reservoir.

Good to know: the position of the MIN and MAX marks and the coolant type vary from one vehicle to another. That is why you go through the manual.

The level should sit at the MAX mark. If it drops again at later checks, a leak still needs to be found: go to the “If nothing works” section.

Solution 2: no air at all, check the fuse and the blower motor

If the fan no longer blows at all, look at the fuse, the blower motor and the blower resistor. Keep the ignition off while you handle fuses.

Advertisement
  1. Find the blower motor fuse using the owner’s manual.
  2. Check the condition of that fuse.
  3. Test the blower motor with a multimeter if the fuse is good.
  4. Then test the blower resistor or regulator with a multimeter.

Tip: a fan that works only on some speeds points to the blower resistor, the part that sets the blower motor’s speed.

The fan should blow at every speed.

To check the fuse and test the blower motor, here is what you need to check and replace in a few minutes.

  • Assortment of 306 car fuses, standard and mini blade, with puller and testerA box of spare blade fuses in the common ratings, with a puller and a tester to check them. Handy to keep in the glove box.AmazonSee at Amazon
  • AstroAI digital multimeter, 2000 countsMeasures DC and AC voltage, current and continuity. Lets you check whether a socket or a fuse really delivers power.AmazonSee at Amazon

Solution 3: bleed the air out of the cooling system

An air bubble in the system stops hot coolant from flowing through the heater core, the small radiator that warms the air sent into the cabin. Start bleeding with a cold engine.

Warning: as it heats up, the coolant, the hoses and the reservoir become scalding, and hot fluid can spray out of an open reservoir. Wear gloves and safety glasses, and squeeze the hoses while they are warm, not hot. If in doubt, switch the engine off and let it cool before you close the cap.

  1. Make sure the engine is cold before you open the reservoir cap.
  2. Set the heater to maximum.
  3. Fill the reservoir with the cap open.
  4. Start the engine and let it run for a few minutes with the cap open.
  5. Watch the level: it can drop when the thermostat opens.
  6. Top up the level.
  7. Squeeze the hoses by hand to push the air out, while they are warm and with gloves on.
  8. Close the cap, after switching off the engine and letting it cool if in doubt.
  9. Take the car for a test drive.

Warning: while the engine runs, the radiator fan can switch on. Keep your hands, sleeves and tools away from its blades.

Once the engine is at temperature, the heater should blow hot air.

For bleeding, gloves and safety glasses reduce the risk of splashes of hot coolant.

  • Mechanix Wear Original Covert mechanic glovesClose-fitting work gloves that protect the hands during car jobs. They keep a good grip on tools and parts.AmazonSee at Amazon
  • 3M Command 2890SC safety gogglesGoggles that protect the eyes from splashes and dust. Useful when sanding, polishing or handling solvents.AmazonSee at Amazon

Solution 4: temperature gauge stays low, check the thermostat

The thermostat regulates engine temperature. Stuck open, it keeps the engine from reaching its normal temperature: the gauge stays low and the heater barely warms up.

  1. Watch the temperature gauge while driving, with the engine warm.
  2. Remove the thermostat (or have it removed) if the gauge stays low.
  3. Put the thermostat in hot water.
  4. Check that it opens in the hot water.
  5. Replace the thermostat if it does not move.

Warning: the hot water in the test can scald. Handle the thermostat with pliers or gloves, never with bare hands.

Good to know: the exact opening temperature depends on the engine. It is listed in the service manual for your model.

chauffage-voiture-ne-chauffe-plus-2-1024x576 Car heater not blowing hot air: what should you check first?
A temperature gauge that stays low points to the thermostat.

Not used to working on the cooling system? Leave removing the thermostat to a garage.

With a working thermostat, the gauge reaches its normal position once the engine is warm.

Solution 5: clogged heater core or blend door

The heater core is made of thin tubes that can clog. On older cars, a broken or disconnected heater valve or blend door keeps air from passing over the core, even when the controls are set to hot.

  1. Look for signs of a failing heater core: a sweet smell in the cabin, fog on the windshield, fast coolant loss.
  2. Have the heater core flushed with water or compressed air, through its fittings on the firewall side.
  3. Have the heater core replaced if the blockage persists.
  4. On an older car, have the heater valve and the blend door checked.

Good to know: a sweet smell or fog on the windshield, along with fast coolant loss, means a trip to the garage.

Once the core is cleared or the control is repaired, the air comes out hot as soon as the engine is at temperature.

If nothing works

Go to a garage in these cases:

  • the coolant drops again after topping up;
  • the temperature gauge or warning light goes into the hot zone;
  • a sweet smell or fog appears in the cabin;
  • nothing changes after checking the level and the fuse and bleeding the system.

In case of overheating, stop driving. If the temperature sensor is suspect, the garage reads the OBD fault codes (the on-board diagnostic system) with an electronic diagnostic tool.

Have the make, model, year and mileage of the vehicle ready. Describe the symptom: cold air, no air at all, low gauge, hot air only on some fan speeds. Say what you have already done, and how much coolant you added.

If the air conditioning no longer cools either, read our guide on a car AC that is not blowing cold air. For other winter breakdowns, see also what to do when your car battery is dead.

Get your car ready for winter: our toolbox

A few useful accessories to troubleshoot, maintain and keep good visibility when it is cold.

  • AstroAI digital multimeter, 2000 countsMeasures DC and AC voltage, current and continuity. Lets you check whether a socket or a fuse really delivers power.AmazonSee at Amazon
  • Assortment of 306 car fuses, standard and mini blade, with puller and testerA box of spare blade fuses in the common ratings, with a puller and a tester to check them. Handy to keep in the glove box.AmazonSee at Amazon
  • Rain-X 2-in-1 windscreen de-icer with rain repellent, 500 mlMelts frost on the windscreen and wiper blades, then leaves a coating that makes water bead. Handy before freeing blades stuck by ice.AmazonSee at Amazon
  • Mechanix Wear Original Covert mechanic glovesClose-fitting work gloves that protect the hands during car jobs. They keep a good grip on tools and parts.AmazonSee at Amazon
  • 3M Command 2890SC safety gogglesGoggles that protect the eyes from splashes and dust. Useful when sanding, polishing or handling solvents.AmazonSee at Amazon
  • NOCO Boost GB40 1000 A jump starterStarts an engine whose battery is too weak, without a second car. It also works as a power bank to charge a phone.AmazonSee at Amazon

Frequently asked questions

Why is my car heater blowing cold air?

Most often the coolant level is too low. An air bubble in the system, a thermostat stuck open, a clogged heater core or a faulty heater valve give the same symptom. Check the level first, with the engine cold.

Can low coolant stop the heater from working?

Yes, it is the most common cause of a heater that blows cold. Check the level with the engine cold, top up to the MAX mark with the coolant recommended in the manual, then look for a leak on the hoses, the radiator and the water pump. If the level drops again, have the system checked at a garage.

Can a thermostat stuck open stop the heater?

Yes, a thermostat stuck open keeps the engine from reaching its normal temperature, and the heater warms poorly. The typical sign is a temperature gauge that stays low. Dipped in hot water, a good thermostat opens, at a temperature that depends on the engine (see the service manual); if it does not move, replace it.

Why is the fan not blowing at all?

Start with the blower motor fuse, whose location is in the owner’s manual. If it is good, test the blower motor or the blower resistor with a multimeter. A fan that works only on some speeds points to the resistor.

Share this content:

Leave a Reply

Your email address will not be published. Required fields are marked *