This article contains affiliate links: if you buy through them, Wanda-techs earns a commission at no extra cost to you.
When a steam iron stops producing steam, the cause is almost always a setting or limescale. Low water tank, temperature dial too low, steam control on dry: check those first. If nothing changes, scale is clogging the soleplate, the anti-scale rod or the boiler of a steam generator, and you need the descaling method that suits your appliance.
Common symptoms and causes
- The water tank is empty or nearly empty.
- The steam control is on the dry position, the thermostat is too low, or the iron has not finished heating.
- Scale blocks the soleplate holes, the anti-scale rod, or the collector and boiler of a steam generator.
- Steam stops when the iron is still: on irons with a motion sensor, that is normal.
- The water is not suitable (additives, condensation water, pure demineralized water).
- On some Philips models, steam is reportedly cut off until descaling is done. Check this point in the manual.
Before you start
Warning: unplug the appliance from the mains before opening it, and never work on a plugged-in appliance. The capacitors of some appliances (TVs, microwaves, power supplies) stay charged after unplugging: do not touch them. An iron and a steam generator produce scalding steam, and a steam generator boiler is under pressure: never open a filler or drain cap while the appliance is in use.
Warning: opening the appliance may void the warranty, so check the warranty end date first. A descaler the manufacturer does not recommend (white vinegar, citric acid, baking soda) poured into a steam generator can also void it.
Let the appliance cool down before handling it. Allow 30 to 45 minutes for the rod of a Tefal iron, about 1 hour for the collector of a Tefal steam generator, and at least 2 hours to descale a Rowenta or Calor steam generator.
Procedures vary from one model to another. Keep the manual within reach.
Good to know: “Calc Clean” is Philips’ name for its descaling function. Tefal calls it self-clean or autoclean.
Solution 1: check the tank, the steam control and the temperature
- Check the water level in the tank and fill it if it is empty or low.
- Set the steam control to the steam position, not the dry position.
- Set the thermostat between 2 or 3 dots and MAX: below that, a Tefal iron produces no steam.
- On a Philips iron, according to the brand’s support, wait until the orange temperature light goes out before asking for steam, and do not leave the thermostat on 1 dot or on SYNTH.
- Move the iron over the fabric: on a Tefal model with a motion sensor, steam stops when the iron stays still.
- For the steam burst (boost or turbo), keep the tank reasonably full, the thermostat between 3 dots and MAX, and wait a few seconds between presses.
Steam should come out of the soleplate as soon as the iron is hot and moving.
Good to know: a Tefal iron switches itself off after 8 minutes standing on its heel, or after 30 seconds lying flat. That is not a fault. Pick the iron up again.
Solution 2: use the right water
- Empty the tank if it holds water with additives (starch, fragrance, fabric softener), condensation water (dryer, fridge, air conditioner) or rainwater.
- Fill the tank with tap water, which Tefal specifies and De’Longhi allows.
- If your water is very hard, mix 50% tap water with 50% unscented distilled or demineralized water.
- Never pour mineral water, battery water, dehumidifier water, scented ironing water or descaler into the tank.
The tank now holds water the iron accepts. Steam still weak? Move on to the next solution.
Warning: Tefal advises against using store-bought demineralized or distilled water on its own. De’Longhi recommends the 50/50 mix above 27 degrees of water hardness.
Solution 3: clean the anti-scale rod
Some Tefal irons have a removable anti-scale rod in the tank, to be cleaned once a month. No rod on yours? Go to solution 4.
- Unplug the iron and let it cool for 30 to 45 minutes.
- Empty the tank.
- Remove the anti-scale rod by pulling it out from the top.
- Soak it for 4 hours in natural lemon juice or citric acid.
- Rinse it under tap water.
- Put it back without touching its tip.

The rod is clean and back in place: fill the tank and test the steam.
Warning: lemon juice and citric acid are fine for the rod of a Tefal iron. Rowenta and Calor advise against them in the boiler of a steam generator, which is a different part.
Solution 4: descale the iron with the self-clean function
On a Tefal iron:
- Fill the tank up to the MAX mark.
- Set the thermostat to MAX and the steam control to the dry position (DRY).
- Stand the iron on its heel and let it heat for about 5 minutes.
- Unplug the iron.
- Hold it horizontally over the sink.
- Remove the anti-scale rod, or activate the self-clean function, depending on your model.
- Let the steam, water and scale flow out through the soleplate holes.
- Put the anti-scale rod back in place.
- Once the iron is cold, gently vacuum the soleplate holes.
Warning: during this flush, the soleplate releases scalding steam.
The water coming out of the soleplate should be clear, with no white powder. Still white powder? Repeat 2 to 3 times.
On some Philips irons (Philips support procedure, to be confirmed in your manual):
- Place the iron on the anti-scale tray supplied with the appliance.
- Hold down the CALC CLEAN button for 2 seconds.
- Wait about 5 minutes.
- Empty the anti-scale tray.
Steam should return once descaling is finished.
Tip: according to a thread on Darty’s after-sales forum, an iron that has not been descaled for a long time may need two descaling cycles in a row and a cleaning of the soleplate holes. This advice does not come from a manufacturer.
Solution 5: steam generator not producing steam, rinse and descale
Depending on the brand, you rinse a removable collector or descale the whole boiler.
Anti-scale collector of a Tefal steam generator (about every 4 months, depending on the model):
- Unplug the generator and empty the tank.
- Wait about 1 hour for the generator to cool down.
- Lift, then turn the tab to release the collector.
- Remove the collector and rinse its inside.
- Put the collector back.
- Turn the tab a quarter turn to the right to lock it watertight.
The collector is locked, and the generator is ready to go again. Without the collector, the iron does not work.
Descaling a Rowenta or Calor steam generator:
- Unplug the generator and wait at least 2 hours.
- Empty the boiler through the drain cap under the appliance.
- Pour water and the descaler made for steam generators into the boiler, at the dose shown on the bottle.
- Plug the generator back in and wait for the light to show it is ready.
- Press the steam burst control several times.
- Unplug the generator, then empty the boiler.
- Rinse the boiler with clean water until the water runs clear.
- Do a second pass with clean water, using the steam burst.

Steam should regain its strength, and the maintenance light may go out.
Warning: Rowenta and Calor advise against white vinegar, baking soda, citric acid and household products in a steam generator. They can damage the seals and the boiler, leave residue and void the warranty.
Rowenta and Calor recommend descaling every month if you iron several times a week, about every 2 months otherwise, or as soon as the maintenance light comes on. Scale gives weak steam and slow heating.
Another scaled-up appliance: see our guide to a Nespresso machine that no longer dispenses coffee.
If nothing works
Stop if the self-clean, repeated 2 to 3 times, still lets white powder out: Tefal then advises contacting customer service. The same goes if steam does not come back after descaling and with the right settings. The fault may then come from an internal part, such as the pump, the solenoid valve or the boiler of a steam generator.
Contact the brand’s customer service or an approved repairer. Have the model reference and serial number, the purchase date and the receipt on hand.
If the repair costs more than the appliance is worth, here are three recent models to compare: two irons and a steam generator.
- Rowenta DW4345 Express Steam: 2600 W steam ironSteam iron with a stainless steel soleplate and a built-in anti-scale system. A practical everyday replacement for a scaled-up iron.AmazonSee at Amazon
- Tefal FV6830 Ultragliss Anti-Calc Plus: 2800 W steam ironSteam iron with a Durilium soleplate and a removable limescale collector. Scale can be removed without taking the iron apart.AmazonSee at Amazon
- Calor Pro Express GV7830C0: 6.9 bar high-pressure steam generator2400 W steam generator with a pressing function and a limescale collector. Suited to people who iron a lot of laundry.AmazonSee at Amazon
Another laundry appliance acting up: see our guide to a dryer that no longer heats.
Take better care of your iron: our toolbox
A suitable descaler and low-scale water help keep steam output steady.
- Buhler descaler for irons and steam stations, 375 ml bottleDescaling liquid made for irons and steam stations. Use it according to the appliance maker's instructions.AmazonSee at Amazon
- Auchan Essentiel demineralised water, 5 LLimescale-free water, to mix half and half with tap water when it is very hard. It helps limit scale build-up in an iron.AmazonSee at Amazon
Frequently asked questions
Why has my steam iron stopped producing steam?
A setting is blocking the steam, or scale is clogging the circuit. Check that the tank is filled, that the control is not on dry, and that the thermostat is at least on 2 or 3 dots. On an iron with a motion sensor, steam also stops when the iron stays still.
How do I descale a steam iron?
Run the self-clean described by the manufacturer: tank at MAX, thermostat at MAX, iron heated for about 5 minutes, then flush over the sink through the soleplate. If your iron has an anti-scale rod, soak it for 4 hours in lemon juice or citric acid once a month.
What water should I put in a steam iron?
Tap water suits most Tefal and De’Longhi irons. If it is very hard, mix it half and half with demineralized or distilled water. Avoid scented water, rainwater, mineral water and condensation water from a dryer, air conditioner or dehumidifier.
How do I unclog the soleplate holes of an iron?
Run the self-clean to flush the scale out through the holes, then gently vacuum the soleplate once the iron is cold. Never scrape the holes with a metal object: Rowenta and Calor advise against it. On a heavily scaled iron, two descaling cycles in a row may be needed, according to user reports.
Why is my steam generator not producing steam?
Scale built up in the boiler gives weak steam and slow heating. Rinse the anti-scale collector (Tefal) or descale the boiler with a descaler made for steam generators (Rowenta, Calor).
Share this content:
