This article contains affiliate links: if you buy through them, Wanda-techs earns a commission at no extra cost to you.
Roomba error 14 (or 1-4, depending on the series) means the robot cannot detect its dust bin, even when the bin is in place. According to iRobot, the cause is almost always a bin that is not fully seated or dirty contacts. Allow about 15 minutes to try everything, from reseating the bin to a reboot (the newsroom’s estimate).
Common symptoms and causes
For iRobot, error 14 means one thing: no installed bin is detected. The code and the message depend on the series:
- 900 series: the robot announces error 14;
- 600, 700 and 800 series: the robot announces error 1-4;
- Wi-Fi 600 and 800 series: the message also tells you to open the iRobot HOME app;
- the troubleshooting light and the full-bin light come on (the 600 series has no full-bin light).
iRobot lists only a few causes:
- bin not seated properly in its slot;
- dirty contacts, on the bin or on the robot;
- faulty bin or contacts, which call for a replacement bin.
Before you start
Take the robot off its charging dock: manual reboots are done off the dock. Identify your model’s series (600, 700, 800, 900, e, i, j or s), because the reboot buttons depend on it.
Have a clean melamine foam sponge (Magic Eraser type) ready, only slightly damp.
Good to know: iRobot’s official error 14 article covers the 600 to 900 series. For the e, i, j and s series, iRobot documents only the reboot steps.
Warning: on the 600 series with a green dot under the bin, the reboot means pulling the battery. Never puncture, bend or heat a lithium battery; a swollen battery will no longer charge and goes to a collection point; work on a non-flammable surface.
Warning: a factory reset erases data, so back up whatever you can first. It deletes all the robot’s settings (maps, schedules, preferences), whereas a reboot keeps them. iRobot asks you to contact its customer care before any factory reset: only run one after that conversation.
Solution 1: reseat the bin properly
A bin that looks in place may not be fully clicked in. This is the first check iRobot asks for.
- Remove the bin from the robot.
- Put the bin back in its slot, making sure it is properly seated.
- Press CLEAN to restart the robot.
Expected result: the robot sets off without announcing error 14 or error 1-4.
Tip: push the bin firmly until it stops, then check that it sits flush with the body across its whole width. A slightly crooked bin may not touch the contacts.

Solution 2: clean the contacts on the bin and the robot
The bin and the robot each have contacts. iRobot asks you to clean both sides, not just the bin.
- Remove the bin from the robot.
- Lightly dampen the clean melamine foam sponge.
- Rub the bin’s contacts with the sponge.
- Rub the robot’s contacts.
- Put the bin back, making sure it is properly seated.
- Press CLEAN to restart the robot.
Expected result: the robot resumes cleaning without reporting the error.
For rubbing the contacts, a melamine sponge does the job.

Mr. Propre Magic Eraser Ultra Power sponge (pack of 2)
This melamine sponge, used barely damp, makes dirty charging contacts on the robot and dock shine again. You use it with water only, no cleaning product.
- AmazonSee at Amazon
Tip: wring the sponge out as much as you can. It should feel barely cool to the touch, and the contacts should be dry before the bin goes back in.
Good to know: iRobot’s error 14 article says nothing about emptying the bin or cleaning the filter. Those are routine maintenance, not among the fixes listed for this code.
Solution 3: reboot the Roomba
A reboot clears many errors. iRobot presents it as always safe: maps, schedules and preferences are kept. On models without Wi-Fi, the clock resets, but the schedule stays.
Error 14: reboot from the iRobot HOME app
Models other than those in the Roomba HOME list below use the classic iRobot HOME app.
- Open the iRobot HOME app.
- Open Product Settings.
- Tap Reboot Roomba.
- Confirm with Reboot Roomba.
For models managed by the Roomba HOME app (Mini, 100/1000, 200/2000, Plus 400/500/600, Max 700/800), the path is Robots > … > Reboot Roomba, using the three-dot menu at the top right, then a confirmation on Reboot Roomba.
With the robot’s buttons (including the Roomba e5)
With the robot off its dock, hold the combination for your series, then release:
- i and s series: hold CLEAN for about 20 seconds.
- j series: hold CLEAN for about 9 seconds.
- 800 and 900 series with Wi-Fi: hold CLEAN for about 10 seconds.
- 500, 600 and 700 series without Wi-Fi, and the e series (Roomba e5 included): hold HOME and SPOT together for about 10 seconds; a tone sounds when you release.
- Mini, 100/1000, 200/2000, Plus 400 to 600 and Max 700/800 models: hold POWER for about 10 seconds, then about 3 seconds to power the robot back on.
Roomba 600 with a green dot under the bin
- Remove the bin.
- Remove the battery.
- Wait 30 seconds.
- Put the battery back in.
- Reinsert the bin.
Expected result: the robot reboots, which can take up to 90 seconds. It no longer reports error 14.
For a different charging problem, see our guide Roomba won’t charge on its dock.
Solution 4: replace the bin
Does the error persist after reseating, cleaning the contacts and rebooting? iRobot then points you to a replacement bin. No official source names a cracked or non-original bin as a cause, but it is the part the manufacturer suggests replacing.
- Order a compatible replacement bin from the iRobot store.
- Remove the old bin.
- Insert the new bin, making sure it is properly seated.
- Press CLEAN to restart the robot.
Expected result: the robot recognizes the new bin and starts its cycle.
If your robot is a Roomba e5, e6 or i7 without a clean base, here is the original bin.

iRobot 4624868: original dust bin with filter for Roomba e5, e6 and i7
Replaces the original bin of the Roomba e5, e6 and i7, filter included. It suits models without an automatic dirt disposal base.
- AmazonSee at Amazon

If nothing works
Stop here if the error comes back after reseating, cleaning the contacts and rebooting, or with a new bin. Contact iRobot customer care before any factory reset, which erases all settings. iRobot’s support article on error 14 points there too.
Keep the robot’s serial number handy. The newsroom suggests noting a few more things:
- the series and model;
- the purchase date;
- the steps already tried (reseating, cleaning, reboot, new bin).
If the robot itself has to be replaced, our comparison Roborock vs Dreame: which robot vacuum to choose will help you pick.
Take better care of your Roomba: our toolbox
Filters, brushes and a spare bin to keep the robot in good shape and avoid the next fault.
- iRobot 4624868: original dust bin with filter for Roomba e5, e6 and i7Replaces the original bin of the Roomba e5, e6 and i7, filter included. It suits models without an automatic dirt disposal base.AmazonSee at Amazon
- iRobot 4624876: 3 high-efficiency filters for Roomba e and i seriesThree replacement filters that trap fine dust in the bin. Changing them regularly keeps suction steady.AmazonSee at Amazon
- iRobot: 3 side brushes for Roomba e, i and j seriesThree replacement side brushes that sweep dirt from edges toward the main brush. Swap them when the bristles are bent or worn.AmazonSee at Amazon
Frequently asked questions
What does error 14 mean on a Roomba?
Error 14 means the robot does not detect an installed bin. 900 series robots announce it as error 14, 600, 700 and 800 series as error 1-4. The troubleshooting light comes on, along with the full-bin light on models that have one.
How do you reset error 14 on a Roomba?
Reseat the bin properly, then press CLEAN to restart the robot. If the error returns, clean the contacts on the bin and the robot, then reboot the robot from the iRobot HOME app or with the button combination for its series. Avoid the factory reset: it erases everything, and iRobot recommends contacting customer care first.
Why does my Roomba no longer detect its bin?
According to iRobot, the bin is badly seated, or its contacts and the robot’s are dirty. Reseating and cleaning with a damp melamine sponge are the fixes iRobot gives for those two cases. If the error persists, the bin or its contacts may be faulty.
Do I need to replace the bin on a Roomba with error 14?
Yes, but only after reseating the bin, cleaning the contacts and rebooting the robot. It is the solution iRobot offers when the error persists, with a replacement bin compatible with your series. If in doubt, contact iRobot customer care with the serial number.
Share this content:
