Advertisement
Cars

Wipers Not Working? What to Check Before Calling a Garage

When wipers stop working, check the basics first: frozen blades, a blown fuse, a rain sensor switched off. If the motor runs but the arms stay still, or the fuse blows again, go to a garage.

7 min read

Car in the rain with a warning signal and a repair wrench
Table of contents
  1. Common symptoms and causes
  2. Before you start
  3. Solution 1: free the blades and check their condition
  4. Solution 2: check the wiper fuse
  5. Solution 3: the motor runs but the arms don’t move
  6. Solution 4: the automatic wipers no longer work when it rains
  7. Solution 5: relay, stalk or wiper motor
  8. If nothing works
  9. Take better care of your wipers: our toolbox
  10. Frequently asked questions
    1. Where is the wiper fuse?
    2. How do I know if the wiper motor is dead?
    3. Can you drive without wipers?
    4. Why have my automatic wipers stopped starting?

This article contains affiliate links: if you buy through them, Wanda-techs earns a commission at no extra cost to you.

When your wipers stop working, start with what you can check yourself: blades stuck to the windshield, a blown fuse or an automatic mode that has been switched off. Allow about twenty minutes and keep the owner’s manual handy. If the motor runs but the arms don’t move, or the fuse blows again, the repair belongs in a workshop.

Advertisement

Common symptoms and causes

  • No wiper moves: a blown fuse or, according to specialist sites, the relay, the stalk (the control lever on the steering column), the motor or a corroded connector.
  • The motor hums or runs, but the arms stay still: according to specialist sites, a loose arm nut or a bent or broken linkage (the rods that connect the motor to the arms).
  • The blades are frozen to the glass, blocked by snow or held by an object, according to specialist sites.
  • The automatic wipers no longer start when it rains: rain sensor switched off, wipers left in service position or, according to forums, a faulty sensor.
  • The rubber on the blades is worn: the blade needs replacing.

Before you start

Have your owner’s manual to hand. It gives the fuse diagram and the way to put the wipers in service position. Keep a spare fuse of the same type and rating nearby, plus a cloth or a piece of cardboard to protect the windshield.

Warning: switch the ignition off. Do not touch airbags, seat belt pretensioners or the high-voltage circuit of a hybrid or electric vehicle. A red warning light means you stop the vehicle, and this procedure does not replace a diagnosis in a workshop.

Warning: never replace a fuse with one of a higher rating or with a foreign object (wire, paper clip). You could damage the electrical system and start a fire.

Warning: a raised arm that snaps back can damage the windshield. Slide a cloth or a piece of cardboard between the glass and the arm. Do not drive in the rain without working wipers: your visibility is no longer assured.

Solution 1: free the blades and check their condition

According to specialist sites, frost or snow can immobilise the blades. A blocked arm can even blow the fuse. Switch the ignition off before touching the arms.

  1. Put the wipers in service position following your vehicle’s manual: on a Polestar 3, this function is activated in the central screen settings.
  2. Place a cloth or a piece of cardboard on the windshield, under each arm.
  3. Clear the snow and de-ice the blades if they are frozen (advice from specialist sites, not found in the manuals consulted).
  4. Clean the windshield and the rubber of the blades.
  5. Examine the rubber of the blades: if it is worn, replace the blade.
  6. Lower the arms and leave service position.

The arms should sweep the windshield again. If nothing moves, go on to the fuse.

Advertisement

If the rubber is worn or hardened, here is a pair of blades to check against the lengths for your vehicle.

essuie-glace-ne-fonctionne-plus-300x169 Wipers Not Working? What to Check Before Calling a Garage

Bosch Aerotwin A297S front wiper blades, 600/500 mm pair

Replaces worn blades or ones hardened by frost with a pair that has a pre-fitted adapter. Check your vehicle's blade lengths before ordering.

essuie-glace-ne-fonctionne-plus-1-1024x576 Wipers Not Working? What to Check Before Calling a Garage
Frost or snow can jam the blades: free them first.

Tip: according to specialist sites, lifting the arms when frost is forecast and using antifreeze washer fluid stops the blades from sticking. This advice does not appear in the manuals consulted.

Solution 2: check the wiper fuse

The location of the fuse box (cabin or engine bay) and the number of the wiper fuse vary from one model to another. Only the diagram in your manual is authoritative. Switch the ignition off before opening the box.

  1. Find the wiper fuse on the fuse diagram in the manual.
  2. Open the fuse box shown on the diagram.
  3. Pull out the fuse, using the puller if your vehicle has one (on the Polestar 2, it is clipped inside the box cover).
  4. Look at the fuse from the side: if the metal element is broken, it has blown.
  5. Replace it with a fuse of the same type, the same colour and the same rating.

Switch the ignition back on and test the wipers: they should work again. If the new fuse blows straight away, see a garage.

To have the right fuse on hand, here is an assortment with a puller and a tester.

essuie-glace-ne-fonctionne-plus-300x169 Wipers Not Working? What to Check Before Calling a Garage

Assortment of 306 car fuses, standard and mini blade, with puller and tester

A box of spare blade fuses in the common ratings, with a puller and a tester to check them. Handy to keep in the glove box.

Tip: photograph the open fuse box before you remove anything. You will know where each fuse goes back.

Advertisement

Good to know: some fuses are not meant to be changed at home. On the Polestar 2, the wiper fuse is a 30 A MCase type under the hood, to be replaced in a workshop. If your manual does not mention the fuse you are looking for, contact the manufacturer’s customer service.

According to car parts sites and forums, some vehicles have two wiper fuses (sweep and return to rest position) and a relay in the engine bay. On vehicles with multiplexed wiring, a control unit runs the wipers.

Solution 3: the motor runs but the arms don’t move

You can hear the motor humming, yet the arms stay still: the problem is mechanical. According to specialist sites, the nut holding the arm on its spindle has worked loose, or the linkage has bent or broken. Switch the ignition off before handling the arms.

  1. Lift the plastic cap at the base of the arm.
  2. Check that the nut under the cap is tight.
  3. If it is loose, realign the arm, then tighten the nut.

The arm should follow the motor’s movement again. If the nut is tight and the arms still don’t move, have the linkage checked in a workshop.

Tip: to realign the arm, mark its rest position with a piece of tape on the windshield before touching it. Remove the tape once the nut is tightened.

Solution 4: the automatic wipers no longer work when it rains

The rain sensor detects water on the windshield and starts the wipers by itself. On the Polestar 2, its owner’s manual covers it in the section on the rain sensor. On another model the control may differ: check your manual.

  1. Set the wiper stalk to position 0 or to single sweep.
  2. Press the rain sensor button to switch it on.
  3. Check that the rain sensor indicator appears on the driver display.
  4. Turn the wheel on the right stalk upwards to increase sensitivity.
  5. Leave service position if you had activated it: the sensor stays off while the wipers are in that position.

The wipers should start as soon as water lands on the windshield. Manual modes work but the automatic one stays silent? According to forums, the sensor may be faulty: have it checked in a workshop.

essuie-glace-ne-fonctionne-plus-2-1024x576 Wipers Not Working? What to Check Before Calling a Garage
The rain sensor switches on with its button, and sensitivity is set with the wheel.

Good to know: on the Polestar 2, the rain sensor switches off when the ignition is turned off, and its state at start-up follows its state at the last switch-off. Turn it off before an automatic car wash: the wipers could start and be damaged.

According to forums and an unofficial bulletin, on some vehicles a sensor badly refitted after a windshield replacement makes the wipers start at random or leaves them unresponsive.

Solution 5: relay, stalk or wiper motor

These faults are not fixed by fitting a part at random. According to specialist sites, each component gives different signs. Note them down before going to the garage.

  1. Note whether the wipers work intermittently, won’t stop or stay dead: according to these sites, this behaviour can come from the relay.
  2. Test the other functions of the same stalk (washer, rear wiper): if they no longer respond either, the stalk is suspected.
  3. Leave the diagnosis to a garage, which will test the circuit with a multimeter.

According to the same sites, a worn motor (brushes, bearings, gears) or a corroded connector are other possible causes. With your observations, the mechanic should be able to point to the faulty part.

If nothing works

Book a garage appointment if the new fuse blows straight away, if the motor hums but the arms don’t move, if the automatic mode stays silent while the manual modes work, or if the fuse is a type that must be replaced in a workshop. For other electrical faults you can check yourself, see also what to do when the battery warning light comes on and checks for a car that won’t start.

Tell the mechanic:

  • which wiper is faulty, front or rear;
  • what happens: nothing, a motor noise, intermittent operation;
  • the state of the fuse and what you have already tried;
  • the make, model, year and registration of the vehicle.

Good to know: in France, a major defect at the contrôle technique (the periodic roadworthiness inspection; a defect that may compromise safety) requires a re-inspection within 2 months. According to specialist sites, a wiper that doesn’t work or a damaged blade would be classed as a major defect, which the official page consulted does not state. For the re-inspection, bring the original unfavourable report and the vehicle registration document.

Take better care of your wipers: our toolbox

A few products to keep good visibility and check your car’s electrical circuit.

  • Bosch Aerotwin A297S front wiper blades, 600/500 mm pairReplaces worn blades or ones hardened by frost with a pair that has a pre-fitted adapter. Check your vehicle's blade lengths before ordering.AmazonSee at Amazon
  • Assortment of 306 car fuses, standard and mini blade, with puller and testerA box of spare blade fuses in the common ratings, with a puller and a tester to check them. Handy to keep in the glove box.AmazonSee at Amazon
  • AstroAI digital multimeter, 2000 countsMeasures DC and AC voltage, current and continuity. Lets you check whether a socket or a fuse really delivers power.AmazonSee at Amazon
  • Rain-X 2-in-1 windscreen de-icer with rain repellent, 500 mlMelts frost on the windscreen and wiper blades, then leaves a coating that makes water bead. Handy before freeing blades stuck by ice.AmazonSee at Amazon

Frequently asked questions

Where is the wiper fuse?

In one of the vehicle’s fuse boxes, in the cabin or under the hood depending on the model. The fuse diagram in your manual shows the exact box and number. On the Polestar 2, for example, it is under the hood and is replaced in a workshop.

How do I know if the wiper motor is dead?

The diagnosis is made in a garage, with a multimeter. According to specialist sites, a worn motor (brushes, bearings, gears) or a corroded connector are among the causes of wipers that no longer respond. A motor that hums without moving the arms points more to the arm nut or the linkage.

Can you drive without wipers?

Not in rain, snow or road spray: without wiping, you can’t see the road. At the contrôle technique, according to specialist sites, a wiper that doesn’t work would be a major defect, with a re-inspection within 2 months.

Why have my automatic wipers stopped starting?

The rain sensor may be switched off, or the wipers were left in service position, which turns it off on the Polestar 2. Switch it back on with its button and check the sensitivity. If the manual modes work and the automatic one stays silent, according to forums, the sensor may be at fault: have it checked.

Share this content:

Leave a Reply

Your email address will not be published. Required fields are marked *