Advertisement
iPhone

Why Is Your iPhone Not Charging? What to Try Before a Repair

Is your iPhone not charging, stopping at 80 % or showing "Liquid Detected"? Test the cable, adapter, port and charging settings before paying for a repair.

7 min read

Smartphone resting next to a wall charger, with an almost empty battery
Table of contents
  1. Common symptoms and causes of an iPhone that won’t charge
  2. Before you start
  3. Solution 1: Test the cable, the adapter and the outlet
    1. If the iPhone won’t charge wirelessly (MagSafe or Qi)
  4. Solution 2: Clean the Lightning or USB-C port
  5. Solution 3: Deal with the “Liquid Detected” alert
  6. Solution 4: The iPhone stops charging at 80 %
    1. On iPhone 15 and later
    2. On iPhone 14 and earlier
    3. For an immediate full charge
    4. If the iPhone stops charging and gets hot
  7. Solution 5: Force restart and update iOS
  8. If nothing works
  9. Take better care of your iPhone: our toolbox
  10. Frequently asked questions
    1. Why does my iPhone stop charging at 80 %?
    2. What should I do when my iPhone says liquid was detected in the connector?
    3. How do I clean an iPhone’s charging port?
    4. Why has my iPhone stopped charging wirelessly?

Updated on November 12, 2026

This article contains affiliate links: if you buy through them, Wanda-techs earns a commission at no extra cost to you.

Advertisement

If your iPhone is not charging, check the cable, the power adapter and the outlet first. Next come the charging port, which is often clogged with lint, and the settings that stop charging at 80 % on purpose. Leave the iPhone on a wall outlet for at least 30 minutes before you decide it is broken.

Common symptoms and causes of an iPhone that won’t charge

  • The iPhone does not charge at all: the cable, adapter or outlet is at fault, the port is dirty or damaged, or the battery is so drained that it needs up to 30 minutes to respond.
  • Charging stops at 80 %: Optimized Battery Charging, the charge limit (iPhone 15 and later) or heat.
  • Charging is slow: the adapter is too weak, or you are using a USB hub or a car outlet.
  • The “Liquid Detected” alert appears: moisture in the connector or on the cable.
  • Only wireless charging fails: a case, poor alignment, an uncertified charger, a USB cable plugged in at the same time, or a non-genuine battery.

Good to know: an iPhone that shows 99 % after a full charge is working normally. Charging indicators can also flicker when you plug in or wake the screen. Wait a moment, then look again.

Before you start

Find out which connector your iPhone has (Lightning or USB-C) and which model it is. The charge limit applies to iPhone 15 and later, and the liquid alert to iPhone XS and later.

Warning: never puncture, bend or heat a lithium battery. A swollen battery will not charge again and belongs at a collection point. Work on a non-flammable surface.

Warning: if the iPhone gets abnormally hot while charging, or if its battery swells, stop using it and have it checked. Keep it away from any heat source and do not use compressed air.

Warning: restoring the iPhone, including the DFU restore suggested by older tutorials, erases all its data. Back up first, or you will lose everything that is not saved (photos, messages, apps). None of the solutions in this guide needs it.

Advertisement

Warning: opening the device can void the warranty, so check when it ends first. A non-genuine battery or parts skew Apple’s diagnostics. Charging a wet connector can corrode its pins.

Solution 1: Test the cable, the adapter and the outlet

  1. Plug the adapter into a wall outlet, not into a computer port or a wireless charger.
  2. Inspect the cable and the adapter. If they have broken or bent pins, stop using them.
  3. Try another outlet, another cable and another power adapter.
  4. Flip the cable around, then unplug it and plug it back in.
  5. Gently wiggle the cable at the connector. If charging cuts out and comes back, the port is probably the culprit.
  6. Use an adapter recommended by Apple: one that is too weak delivers too little power.
  7. If an “accessory not supported” or “not certified” message appears, plug the cable straight into the charger, with no hub in between.
  8. Let it charge for at least 10 minutes before you judge.
refresh-167034-1-1024x576 Why Is Your iPhone Not Charging? What to Try Before a Repair
Try another outlet, another cable and another adapter first.

The charging icon should appear within about 2 minutes. A very drained battery can take 20 to 30 minutes to show any sign of life.

Good to know: according to information we could not verify on Apple’s website, iOS 26 reportedly shows an “Incompatible Charger” notice in Settings > Battery when the charger is too slow. If your iPhone only charges slowly, see also our guide on an iPhone that charges slowly.

If the cable is the problem, here is a certified Apple cable to replace yours.

refresh-167034-300x169 Why Is Your iPhone Not Charging? What to Try Before a Repair

Apple USB-C to Lightning cable, 1 m

Connects a Lightning iPad or iPhone to a USB-C charger or computer. An Apple cable avoids charging faults caused by poor-quality cables.

If the iPhone won’t charge wirelessly (MagSafe or Qi)

  1. Unplug any USB cable from the iPhone: when it is plugged in, it charges through the cable, not wirelessly.
  2. Plug the Qi-certified wireless charger into a wall outlet.
  3. Remove the case if it could get in the way.
  4. Place the iPhone in the center of the charger, screen facing up.
  5. If a MagSafe charger is not detected, try an Apple MagSafe charger.

The charging image should appear. If not, wait up to 10 minutes.

Tip: if the iPhone charges wirelessly but not by cable, the fault is on the cable or port side. This test saves you from replacing a charger that works.

Advertisement

If your wireless charger is the problem, here is a Qi wireless charger to try.

refresh-167034-300x169 Why Is Your iPhone Not Charging? What to Try Before a Repair

Anker PowerWave Pad 10 W Qi wireless charger

A flat Qi pad: set the phone on it and it charges without a cable. It spares the charging port from daily plugging.

Solution 2: Clean the Lightning or USB-C port

  1. Turn off the iPhone.
  2. Unplug all cables.
  3. Look at the port on the bottom of the device for debris.
  4. Brush the port with a soft, dry, non-metallic brush, working outward.
  5. Plug the cable back in firmly.
  6. Let it charge for 30 minutes.

Do not use bleach, hydrogen peroxide or compressed air. Never immerse the iPhone in liquid. After cleaning, the cable should seat cleanly and charging should start.

Solution 3: Deal with the “Liquid Detected” alert

The alert exists on iPhone XS and later, both Lightning and USB-C. Its title varies with the accessory: “Charging Not Available” with a Lightning charger, and “Liquid Detected in USB-C Connector” with a USB-C cable or charger. With a Lightning accessory that is not a charger it reads “Liquid Detected in Lightning Connector”, and with a USB-C accessory, “Liquid Detected”.

  1. Unplug the cable from the iPhone and from the power source.
  2. Gently tap the iPhone with the connector facing down to shake the liquid out.
  3. Leave it in a dry, well-ventilated place.
  4. Wait at least 30 minutes, then try charging again.
  5. If the alert comes back, extend the drying time up to 24 hours.
  6. Once the iPhone is dry, unplug and replug the cable and adapter if it still won’t charge.

Warning: do not put the iPhone in rice, whose particles can damage it. Keep it away from any external heat source and do not use compressed air. Do not insert anything into the port, neither a cotton swab nor a paper towel.

The alert should clear, sometimes after a full day. Apple lets you dismiss it to charge in an emergency but advises against it, because charging a wet port risks corroding the pins.

Wireless charging remains possible with a Qi-certified charger if the back of the iPhone is dry.

refresh-167034-2-1024x576 Why Is Your iPhone Not Charging? What to Try Before a Repair
After the liquid alert, let it dry for at least 30 minutes, up to 24 hours.

Solution 4: The iPhone stops charging at 80 %

On iPhone 15 and later

  1. Open Settings > Battery > Charging.
  2. Set the charge limit to 100 %. It ranges from 80 to 100 % in steps of 5 %.

On iPhone 14 and earlier

  1. Open Settings > Battery > Battery Health & Charging.
  2. Turn off Optimized Battery Charging if you want a full charge. Keep in mind that turning it off can speed up battery wear.

For an immediate full charge

  1. Touch and hold the charging notification on the Lock Screen, which shows the estimated finish time.
  2. Tap Charge Now.

If the iPhone stops charging and gets hot

  1. Move the iPhone and its charger somewhere cooler.

Charging should resume past 80 %. Optimized Battery Charging learns your routine over at least 14 days and only delays charging when it expects a long stretch on the charger.

Good to know: with a limit below 100 %, the iPhone stops a few points short of it. It resumes if the level drops by more than 5 %. It sometimes climbs to 100 % to recalibrate its estimate.

Solution 5: Force restart and update iOS

On iPhone 8 and later, and iPhone SE (2nd generation) and later:

  1. Press and quickly release the volume up button.
  2. Press and quickly release the volume down button.
  3. Hold the side button until the Apple logo appears.
  4. Leave the iPhone charging for 30 minutes.
  5. Install the latest version of iOS in Settings > General > Software Update.

On iPhone 7 and 7 Plus, hold the side button and the volume down button until the Apple logo appears. On iPhone 6s, iPhone SE (1st generation) and earlier, hold the side button and the Home button.

The Apple logo should appear, followed by the charging indicator. The update path comes from our previous version of this guide, so it may differ slightly depending on your iOS version.

If nothing works

Stop if the iPhone still won’t charge after 30 minutes on a wall outlet, a force restart, another cable, another adapter and a clean port. Do the same if the liquid alert comes back every time with Apple accessories: a repair may be needed.

If the alert only appears with one particular cable, that cable is probably damaged. Contact its manufacturer.

A non-genuine or unknown battery can cause false wireless or MagSafe charging failures, charging stuck at 1 % or lower, and unexpected shutdowns. Apple technicians check the battery with a diagnostic tool and replace it if it is unknown and shows these faults.

Contact Apple Support at getsupport.apple.com or an authorized repair provider (support.apple.com/repair).

We could not verify the current price of a battery replacement, so ask for a quote before any work is done. If your battery also drains too fast, read our guide on iPhone battery draining fast on iOS 26.

Take better care of your iPhone: our toolbox

A few reliable accessories to charge your iPhone safely and keep your data protected.

  • Anker Nano 20 W USB-C wall charger (PowerPort III)Compact fast charger for phones with a USB-C port. It fits easily in a bag or a travel pouch.AmazonSee at Amazon
  • Anker 140 W braided USB-C to USB-C cable, 1.2 mCharges and syncs USB-C iPads and laptops. The braided sheath resists daily bending.AmazonSee at Amazon
  • Anker Nano power bank 10,000 mAh 45 W with retractable USB-C cablePortable battery with a built-in retractable USB-C cable to top up a tablet away from a socket. Handy as a backup when the wall charger is out of reach.AmazonSee at Amazon
  • SanDisk iXpand Flash Drive Luxe 128 GB, Lightning and USB-C for iPhoneA flash drive with Lightning and USB-C connectors to copy photos and files from an iPhone. Also plugs into a computer to store the copy.AmazonSee at Amazon

Frequently asked questions

Why does my iPhone stop charging at 80 %?

Optimized Battery Charging, the charge limit or heat stops charging at around 80 %. On iPhone 15 and later, check the limit in Settings > Battery > Charging. If the iPhone is too hot, charging resumes once it has cooled down.

What should I do when my iPhone says liquid was detected in the connector?

Unplug the cable, tap the iPhone with the connector facing down and let it dry in a ventilated place for at least 30 minutes. The alert can take up to 24 hours to clear. Do not use rice, heat or compressed air.

How do I clean an iPhone’s charging port?

Turn off the iPhone, unplug everything, then brush the port outward with a soft, dry, non-metallic brush. Do not use any liquid or compressed air. Then plug the cable back in firmly and let it charge for 30 minutes.

Why has my iPhone stopped charging wirelessly?

A case, poor alignment, a charger that is not Qi-certified or a USB cable plugged in at the same time can block wireless charging. Remove the case, center the iPhone screen up and wait up to 10 minutes. A non-genuine battery can also cause this fault.

Share this content:

Leave a Reply

Your email address will not be published. Required fields are marked *