Advertisement
Cars

Windshield washer not working: what can you check yourself?

A windshield washer that no longer sprays is most often caused by an empty reservoir, frozen fluid or a clogged nozzle. Here is how to check each cause yourself, from the reservoir to the pump.

6 min read

Car with a drop of fluid, a diagnostic magnifier and a repair wrench
Table of contents
  1. Common symptoms and causes
  2. Before you start
  3. Solution 1: check the reservoir level and the fluid
  4. Solution 2: frozen washer fluid, how to thaw it safely
  5. Solution 3: clogged washer nozzle, how to clear it
  6. Solution 4: check the washer fuse
  7. Solution 5: washer pump and hoses
  8. If nothing works
  9. Take better care of your washer system: our toolbox
  10. Frequently asked questions
    1. Why does my windshield washer not spray when I can hear the pump?
    2. How do I unclog a windshield washer nozzle?
    3. Where is the windshield washer fuse?
    4. What should I do if the washer fluid has frozen?
    5. Can I put water in the washer reservoir?

This article contains affiliate links: if you buy through them, Wanda-techs earns a commission at no extra cost to you.

Your windshield washer is not working and the glass stays dry when you pull the lever? Listen to the pump first. If you hear it running but nothing comes out, a nozzle or hose is clogged or disconnected; if you hear nothing, the fuse, the connector or the pump is at fault.

Advertisement

Either way, check the fluid level in the reservoir first.

Common symptoms and causes

  • Nothing sprays and the pump makes no sound: empty reservoir, blown fuse, faulty connector or pump, or a bad relay or column stalk (the control lever on the steering column).
  • The pump hums but nothing comes out: clogged nozzle, or a hose that is clogged, cracked or disconnected, or frozen fluid.
  • Only one side sprays: the nozzle on the dry side is probably clogged.
  • Fluid drips under the car: leaking reservoir or hose, or a disconnected hose.

If it is the wiper blades that no longer move, see our guide on wipers that stopped working.

Before you start

Have the owner’s manual at hand (fuse box location and amperage), a fine needle, white vinegar and winter washer fluid. A multimeter is optional, for the voltage test.

Warning: switch off the ignition; do not touch airbags, seat belt pretensioners or the high-voltage system of a hybrid or electric vehicle; a red warning light means you must stop driving; this procedure does not replace a diagnosis in a workshop. Turn the engine off before opening the hood. Only the tests in Solutions 4 and 5 are done with the ignition on, at the moment indicated.

Warning: do not pour boiling water on the windshield, as the thermal shock can damage it.

Warning: switch off the ignition before touching a fuse, and replace it only with a fuse of the same amperage. Wiring and relays are a job for a garage.

Advertisement

As a precaution, although our sources do not go into detail: never put engine antifreeze in the washer reservoir.

Good to know: never run the washer with an empty reservoir. It damages the pump.

Solution 1: check the reservoir level and the fluid

An empty reservoir is the most common cause. With the engine off, open the hood.

  1. Find the washer reservoir cap in the engine compartment, often on the passenger side.
  2. Check the fluid level.
  3. Look under the car and around the reservoir: a crack or a puddle means a leaking reservoir or hose.
  4. Fill it with a non-abrasive washer fluid; in cold weather, choose an antifreeze “winter” fluid.

Then pull the lever: the fluid should spray onto the windshield. If the level drops fast without you using the washer, look for the leak in Solution 5.

For winter, here is a ready-to-use fluid that resists freezing.

lave-glace-ne-fonctionne-plus-300x169 Windshield washer not working: what can you check yourself?

Michelin 009291 winter windscreen washer fluid -20 °C, 4 L

Ready-to-use fluid that cleans the glass and protects the washer circuit from frost down to -20 °C. Pour it straight into the reservoir.

Solution 2: frozen washer fluid, how to thaw it safely

Plain water freezes in winter. As it expands, the ice can burst the hoses or the reservoir. The advice in this solution comes mostly from unofficial sources.

Advertisement
  1. Stop using the washer: according to a specialist source, running the pump on frozen fluid can blow the fuse or destroy the pump.
  2. Let the fluid thaw, preferably by parking the car in a heated garage.
  3. If you cannot wait, an unofficial source suggests pouring warm water, never boiling, into the reservoir a little at a time.
  4. Once the fluid has thawed, replace it with winter fluid.
  5. In freezing weather, turn on the windshield defroster and wait until the glass is warm before using the washer, or the fluid will freeze on the glass and block your view.
lave-glace-ne-fonctionne-plus-1-1024x576 Windshield washer not working: what can you check yourself?
Frozen fluid: let it thaw rather than running the pump.

The fluid should reach the windshield again. After a freeze, check that nothing leaks under the car.

To keep good visibility in winter, see also how to remove fog from the windshield.

Solution 3: clogged washer nozzle, how to clear it

The nozzle is the small jet that sprays fluid onto the windshield. Only one side sprays? The nozzle on the dry side is probably clogged.

  1. Take a fine needle, a pin or an unfolded paper clip, thinner than the nozzle opening.
  2. Gently insert it into the opening while turning, without forcing it so you do not widen the jet.
  3. Test the washer after each attempt.
  4. For limescale, lay a cloth soaked in white vinegar, diluted half and half in warm water, on the nozzle for 5 to 10 minutes.
  5. Rinse with clean water.
  6. If you have compressed air, blow in short bursts, with the tip a few centimeters from the nozzle.

Both nozzles should now spray a clean jet.

Warning: air that is too strong can pop the hoses off or damage the seals.

Good to know: some nozzles can be aimed one by one, others cannot, depending on the model. Never force a nozzle to reposition it. If the spray stays weak or off-target after cleaning, the nozzle is worn and needs replacing.

Solution 4: check the washer fuse

No pump sound and a full reservoir? Check the fuse, with the ignition off.

  1. Open the owner’s manual at the fuse page to find the location and amperage of the washer fuse.
  2. Open the fuse box, under the dashboard or in the engine compartment; the diagram is often under the cover.
  3. Pull out the indicated fuse and look at the wire inside: if it is broken, the fuse is blown.
  4. Replace it with a fuse of the same amperage.

Then switch the ignition on and use the washer: you should hear the pump again. A new fuse that blows again points to a fault, according to unofficial sources. Have a garage check the circuit, and never fit a stronger fuse.

If the fuse is blown, an assorted kit lets you keep the right amperage on hand.

lave-glace-ne-fonctionne-plus-300x169 Windshield washer not working: what can you check yourself?

Assortment of 306 car fuses, standard and mini blade, with puller and tester

A box of spare blade fuses in the common ratings, with a puller and a tester to check them. Handy to keep in the glove box.

Solution 5: washer pump and hoses

This solution takes a bit more confidence. The hose test is mentioned by only one specialist source.

Tip: before step 2, place a container under the hose. Fluid may run out when you disconnect it.

  1. If the pump hums but nothing comes out, look under the vehicle: fluid dripping signals a torn, cracked or disconnected hose.
  2. Disconnect the hose at the outlet, toward the nozzle, and pull the lever with the ignition on.
  3. If fluid flows from the hose, the nozzle is clogged: go back to Solution 3.
  4. If nothing flows, the hose or the circuit is clogged.
  5. If you cannot hear the pump, find it under or on the reservoir.
  6. With the ignition on, measure the voltage at the pump connector with a multimeter while the lever is pulled.

With 12 V at the connector, the fuse and wiring are fine: the pump (the washer motor) needs replacing. Without 12 V, the problem is electrical (connector, relay or column stalk) and is a job for a garage.

lave-glace-ne-fonctionne-plus-2-1024x576 Windshield washer not working: what can you check yourself?
With a multimeter, the voltage at the connector tells the pump from the electrical circuit.

If nothing works

Stop and take the car to a garage in these cases: no 12 V at the pump although the fuse is good, a pump that does not react although it receives 12 V, a fuse that blows again, or a suspect relay, column stalk or wiring. Keep the owner’s manual, the model and the year of the vehicle at hand. Also describe what you have already tested.

Do not wait if an inspection is coming up. Under the 2019 French technical instruction, which we could read only in part, a washer that does not work at all counts as a major failure, with a re-inspection within 2 months. A low fluid level with a working pump, or misaligned jets, count as minor, and rules differ outside France.

Take better care of your washer system: our toolbox

A few products to maintain the washer circuit and get you out of trouble before winter.

  • Michelin 009291 winter windscreen washer fluid -20 °C, 4 LReady-to-use fluid that cleans the glass and protects the washer circuit from frost down to -20 °C. Pour it straight into the reservoir.AmazonSee at Amazon
  • Assortment of 306 car fuses, standard and mini blade, with puller and testerA box of spare blade fuses in the common ratings, with a puller and a tester to check them. Handy to keep in the glove box.AmazonSee at Amazon
  • AstroAI digital multimeter, 2000 countsMeasures DC and AC voltage, current and continuity. Lets you check whether a socket or a fuse really delivers power.AmazonSee at Amazon
  • AABCOOLING 750 ml compressed air dusterDry air spray with a thin tube to blow dust and deposits out of hard-to-reach places. Odourless, it also cleans keyboards and connectors.AmazonSee at Amazon
  • Rain-X 2-in-1 windscreen de-icer with rain repellent, 500 mlMelts frost on the windscreen and wiper blades, then leaves a coating that makes water bead. Handy before freeing blades stuck by ice.AmazonSee at Amazon

Frequently asked questions

Why does my windshield washer not spray when I can hear the pump?

The fluid is blocked between the pump and the windshield: a clogged nozzle or hose, or a disconnected hose. The fluid may also be frozen. Disconnect the hose on the nozzle side and pull the lever: if fluid flows, the nozzle is clogged.

How do I unclog a windshield washer nozzle?

Gently insert a fine needle or an unfolded paper clip into the opening while turning, then test. Against limescale, lay a cloth soaked in white vinegar diluted half and half in warm water on it for 5 to 10 minutes, then rinse with clean water. Do not force it: you may widen the jet.

Where is the windshield washer fuse?

In the fuse box, under the dashboard or in the engine compartment depending on the vehicle. The owner’s manual gives its exact location and amperage, and the diagram is often under the fuse box cover.

What should I do if the washer fluid has frozen?

Stop using the washer and let it thaw, preferably in a heated garage. An unofficial source suggests pouring warm water, never boiling, into the reservoir a little at a time. Then replace the fluid with winter fluid.

Can I put water in the washer reservoir?

Not in winter: plain water freezes, and the ice can burst the hoses or the reservoir. In cold weather, use antifreeze washer fluid. Never pour engine antifreeze into it.

Share this content:

Leave a Reply

Your email address will not be published. Required fields are marked *