Updated on October 31, 2026
This article contains affiliate links: if you buy through them, Wanda-techs earns a commission at no extra cost to you.
LG TV problems are usually solved around the set first: the power outlet, the HDMI source, the box or the audio output, depending on the symptom. Run these checks before any reset.
Common symptoms and causes
- The TV stays off and the standby light too: power supply, outlet or circuit breaker.
- The screen stays black, with or without sound: source, HDMI cable, set-top box or TV.
- Wi-Fi won’t connect: router, internet provider, password, date and time.
- The sound is gone: audio output set to another device, muted soundbar, HDMI ARC link set up wrong.
Before you start
Find out which webOS version you have, the system on LG TVs: press the Settings button (the cog) or Mute on the remote 3 times. Menus change with the year and the model. Also write down the model number: you need it to find the software for a USB update.
Warning: unplug the TV from the mains before any hands-on work, and never touch a set that is plugged in. Do not open the casing: a TV’s capacitors stay charged after unplugging, so do not touch them.
Warning: opening the device may void the warranty. Check the warranty end date first.
Warning: the factory reset in solution 5 erases apps, accounts and settings. Back up what you can and note your logins first.
Solution 1: the LG TV won’t turn on
- Look at the standby light at the bottom of the TV: it should be on.
- If it is off, unplug the power cord at the TV end and at the outlet, then plug it back in firmly. With a built-in cord, work on the outlet side only.
- Plug another device into the same outlet to test it.
- If that device doesn’t work either, check the circuit breaker.
- Press the power button on the TV, under the logo or on the back.
- If the TV turns on this way, replace the remote’s batteries.
- Point the remote at the camera of an Android phone and press a key.
A flash should show on the phone’s screen. This test may fail with an iPhone.
A TV that starts with its button but not with the remote points to the remote or its sensor. The rest is in our guide on a TV remote that no longer works.
Tip: during these tests, plug the TV straight into the wall outlet. A worn power strip gives the same symptoms as a failed power supply.
If the original remote is lost or dead, here is an LG pointer remote for webOS TVs.

LG Magic Remote MR23GN (2023) remote control
Pointer and voice remote for LG webOS TVs. It replaces a lost or faulty remote, with the same on-screen pointing.
- AmazonSee at Amazon
Solution 2: LG TV black screen, with or without sound
Good to know: these checks come from a summary of an LG help page and may vary by model.
- Press a volume key while the screen is black.
- See whether the volume bar appears: if it does, the source or the cable is at fault; if not, the TV is.
- Change input with the Input or Source button.
- Plug the cable into another HDMI port.
- Unplug the HDMI cable at both ends, then plug it back in.
- If you use a set-top box, unplug its power for 5 seconds, then plug it back in.
- Unplug the TV’s power cord.
- Hold the Power button on the TV for about 10 seconds.
- Plug the cord back in.
If the picture returns, stop there. Steps 7 to 9 are a hardware reset, different from the factory reset in solution 5.
Tip: keep a second HDMI cable handy. A damaged cable can pass for a dead TV.

If another cable fixes the problem, here is a quality HDMI 2.1 cable to replace the old one.

Belkin Ultra High Speed HDMI 2.1 cable, 2 m
Carries 4K and 8K picture and sound between a box, console or soundbar and the TV. A worn or bent cable can cause a black screen.
- AmazonSee at Amazon
A black screen with no menu and no volume bar may mean the TV needs a repair: skip to “If nothing works”.
Solution 3: LG TV problem with Wi-Fi or apps
The Wi-Fi menu depends on your webOS version:
- webOS 6.0 and later (2021 onwards): Settings > All Settings > General > Network > Internet Connection > Wi-Fi Connection
- webOS 5.0 (2020): Settings > All Settings > Connection > Network Connection Settings > Wi-Fi Connection
- webOS 4.5 (2019): All Settings > Connection > Wi-Fi Connection
- webOS 4.0 and earlier: All Settings > Network > Wi-Fi Connection
- Open the Wi-Fi menu for your version and enter the password, mind the upper and lower case.
- Unplug the modem and the router, and wait about 10 seconds.
- Plug the modem back in and wait about 1 minute.
- Plug the router back in and wait for the internet light.
- Turn on your smartphone’s hotspot and connect the TV to it.
- Connect the TV to the router with an Ethernet cable: it connects automatically.
- On webOS 6.0 and later, open All Settings > General > System > Time & Timer and set the date and time by hand if the automatic setting fails.
Check that the TV connects and your apps open. Connected to the phone but not to the router? The problem lies with the router or the internet provider.
If the Wi-Fi stays weak in the living room, here is an Ethernet cable to link the TV to the router, or a repeater to boost the signal.
- UGREEN Cat 6 Ethernet cable, 5 mConnects a PC straight to the router for a stable wired connection. Handy for testing the network or working while Wi-Fi is down.AmazonSee at Amazon
- TP-Link RE315 AC1200 dual-band Wi-Fi repeaterExtends the Wi-Fi signal into a room the router reaches poorly. Dual-band, it works on 2.4 GHz and 5 GHz.AmazonSee at Amazon
Good to know: an LG help snippet also advises turning off Quick Start and SIMPLINK, only for the length of a test: solution 4 needs SIMPLINK on. We could not read that full page, nor the one for step 7.
Once the connection is back, see the apps to download on an LG smart TV or how to install third-party apps on an LG TV.
Solution 4: LG TV, no sound from the soundbar
These steps apply to an external audio device connected over HDMI ARC or eARC (the port that sends the TV’s sound to that device). The paths come from LG’s UK help: the English labels are the ones to look for, though your menu may differ.
- Check that the soundbar is on and not muted, with the volume above 0.
- Select the right input on the soundbar.
- Plug it into the HDMI ARC or eARC port with a CEC-compatible High-Speed cable, CEC being the protocol that lets HDMI devices control each other.
- Open Settings > All Settings > Sound > Sound Out and choose the output in use: HDMI(ARC) Device, Optical, Bluetooth or Wi-Fi.
- Open Settings > General > External Devices > HDMI Settings > SIMPLINK (HDMI-CEC) and set it to On.
- If the sound is still missing, turn off the TV and the audio device, then turn them back on.
- Reconnect the HDMI cable at both ends.
Test the sound after each step and stop as soon as it returns.
Good to know: steps 6 and 7 are still to be confirmed for your model. LG also mentions a sound self-test, Sound Self-Diagnosis, under All Settings > Support on webOS 6 and later, on a page we could not read.
Solution 5: update or reset the LG TV
Update over the internet
Warning: do not unplug the TV or cut the internet during the update. The screen may go dark or freeze: wait, about 5 to 10 minutes, up to 20 according to LG pages.
- On webOS 5.0 and later (2020 onwards), open Settings > All Settings > Support > Software Update.
- On webOS 4.5 and earlier, open Settings > All Settings > General > About This TV > check for updates.
- On a 2020 or later TV, turn on Settings > All Settings > Support > Software Update > Auto Update > On.
The TV installs the new version. If it is already up to date, nothing changes.
Update with a USB drive
Warning: do not unplug the TV during the update, even if the screen goes dark or freezes.
- Download the software from the LG website with your model number, then extract the archive.
- Prepare a USB drive formatted as FAT32 or NTFS.
- Create the
LG_DTVfolder at the root of the drive. - Put the
.epkfile in that folder. - Plug the drive into the TV and follow the on-screen prompts.
Tip: formatting a drive erases its contents. Copy them to a computer first.

Good to know: according to an LG help snippet, a .bin file is unzipped at the root of the drive, with no folder.
Factory reset
The path depends on your version, and the label varies across LG pages:
- webOS 6.0 and later (2021 to 2025): Settings > All Settings > General > System > Reset to Initial Settings
- webOS 5.0 (2020): All Settings > Support > Reset to Initial Settings
- 2019 and earlier (webOS 4.5): All Settings > General > Reset to Initial Settings
Warning: the next step erases data. Apps, signed-in accounts and settings will be lost. Back up what you can and note your logins first.
- Open the menu for your version.
- On recent models (webOS 24 and 25), choose to reset everything, network included, or to reset everything except the network.
- Leave the TV plugged in until the process ends.
The TV goes back to its initial settings.
If nothing works
Stop if the screen stays black with no menu and no volume bar, if the light stays off with a tested outlet, or if the Wi-Fi list stays empty. Do not open the TV.
Contact LG through its help page: the site’s chatbot, or a request for a technician visit. Have the model number, the serial number and the webOS version ready. The visit is charged outside the warranty.
Take better care of your LG TV: our toolbox
These accessories help LG TV owners connect, power and maintain their TV.
- Belkin Ultra High Speed HDMI 2.1 cable, 2 mCarries 4K and 8K picture and sound between a box, console or soundbar and the TV. A worn or bent cable can cause a black screen.AmazonSee at Amazon
- LG Magic Remote MR23GN (2023) remote controlPointer and voice remote for LG webOS TVs. It replaces a lost or faulty remote, with the same on-screen pointing.AmazonSee at Amazon
- UGREEN Cat 6 Ethernet cable, 5 mConnects a PC straight to the router for a stable wired connection. Handy for testing the network or working while Wi-Fi is down.AmazonSee at Amazon
- TP-Link RE315 AC1200 dual-band Wi-Fi repeaterExtends the Wi-Fi signal into a room the router reaches poorly. Dual-band, it works on 2.4 GHz and 5 GHz.AmazonSee at Amazon
- LG SP2 2.1 soundbar, 100 W, HDMI ARC and BluetoothImproves TV sound with a built-in subwoofer. It connects through HDMI ARC and also accepts Bluetooth.AmazonSee at Amazon
- Belkin 4-outlet surge protector, 525 joules, 2 m, 2 USB portsPower strip with surge protection that shields chargers and devices from voltage spikes. Its two USB ports also free up a socket.AmazonSee at Amazon
- Mistify screen cleaning spray 500 ml with 2 microfibre clothsCleans screens and glass surfaces without leaving streaks. The two microfibre cloths are soft and lint-free.AmazonSee at Amazon
- SanDisk Ultra Dual Drive Go 128 GB, USB-C and USB-A flash driveUSB key with two connectors, for a computer or a phone. Handy for carrying files or a software update.AmazonSee at Amazon
Frequently asked questions
Why won’t my LG TV turn on?
Look at the standby light: if it is off, check the cord, the outlet or the circuit breaker. If the TV’s button turns it on, the remote or its sensor is at fault. If the light stays off with a tested outlet, contact LG.
How do I reset an LG TV?
Go through the settings: on webOS 6.0 and later, open Settings > All Settings > General > System > Reset to Initial Settings. This deletes the apps, signed-in accounts and settings.
Why does my LG TV have a black screen with sound?
The source, the cable or the TV may be at fault, and the volume key settles it. According to an LG help page seen only as a summary, a visible volume bar points to the source or the cable. If it is missing, the TV is to blame and may need a repair.
How do I update an LG TV?
On webOS 5.0 and later, open Settings > All Settings > Support > Software Update. Without internet, use a USB drive with an LG_DTV folder holding the .epk file. Never unplug the TV during the process.
Why does my LG TV no longer connect to Wi-Fi?
Check the password, the router and the internet provider first. Test the connection, restart the modem and the router, then try a smartphone hotspot.
Share this content:
