Advertisement
Farm and garden equipment

Pressure washer losing pressure: what should you check?

Your pressure washer has lost pressure or it fluctuates? Check the water supply, bleed the air, clean the filter and nozzle, then look for leaks.

6 min read

Water drop, warning sign, magnifier and wrench for diagnosing a loss of pressure
Table of contents
  1. Common symptoms and causes
  2. Before you start
  3. Solution 1: check the water supply
  4. Solution 2: bleed the air from the pump
  5. Solution 3: clean the water inlet filter
  6. Solution 4: clear the nozzle and check the lance
  7. Solution 5: look for leaks
  8. If nothing works
  9. Take better care of your pressure washer: our toolbox
  10. Frequently asked questions
    1. Why has my pressure washer lost pressure?
    2. How do I bleed the air from a pressure washer?
    3. How do I unclog a pressure washer nozzle?
    4. Why does my Kärcher pulse or surge?
    5. How do I protect a pressure washer from frost?

This article contains affiliate links: if you buy through them, Wanda-techs earns a commission at no extra cost to you.

Your pressure washer has lost pressure: the motor runs, but the jet is weak or uneven. Kärcher manuals name three causes when pressure won’t build: too little incoming water, a clogged inlet filter, or air in the machine. Start at the tap.

Advertisement

Common symptoms and causes

  • Pressure won’t build: too little incoming water, a clogged water inlet filter, or air in the pump.
  • Pressure fluctuates: a clogged nozzle or an insufficient water flow.
  • The pump vibrates: air in the system or, according to the manual of a professional Kärcher model, a blocked or leaking supply line.
  • The jet went weak after a lance adjustment: the detergent or low-pressure setting might reduce pressure, but the manuals don’t confirm it.
  • The machine spent the winter without being drained: frost may have damaged it.
  • None of the above: advice sites point to a worn pump, valves or pressure switch; the manuals don’t mention them.

Before you start

Keep your model’s manual within reach. Water supply values vary from one machine to another. Open the tap fully before every test.

Warning: unplug the machine from the mains before opening it, and never work on a machine that is plugged in. The capacitors in some appliances (TVs, microwaves, power supplies) stay charged after unplugging: don’t touch them. Never point the jet at a person, an animal, live electrical equipment or the machine itself.

Warning: opening the machine may void the warranty, so check the warranty end date first. Beyond the routine upkeep described here, the pump and any repairs are a job for an authorized service center.

Before you disconnect a hose or remove a part, release the pressure in the machine:

  1. Release the trigger on the spray gun.
  2. Close the tap.
  3. Squeeze the trigger for 30 seconds.
  4. Lock the trigger.
  5. Set the switch to 0/OFF.
  6. Unplug the machine from the mains.

The system is no longer under pressure: you can detach the hose without risk of spray.

Warning: if pressure doesn’t build within 2 minutes, switch the machine off. The pump would be running dry, meaning without water, and that damages it.

Advertisement

For the same reason, switch the machine off (0/OFF) during any break longer than 5 minutes. Never leave it running unattended.

Hold the spray gun and lance firmly during the tests: the jet kicks back. If the motor’s thermal protection trips, set the switch to 0/OFF and let the machine cool down for 1 hour.

Solution 1: check the water supply

Too little incoming water stops the pressure from building. It’s the simplest check.

  1. Open the tap fully.
  2. Look up the minimum flow required on the rating plate or in the manual: 8 l/min (about 2.1 gal/min) for a Kärcher K2, 10 l/min (about 2.6 gal/min) for a K5.
  3. Check that the incoming water doesn’t exceed 40 °C (104 °F) and that the mains pressure stays below 1.2 MPa (12 bar, about 174 psi).
  4. For a Kärcher K5, the manual calls for a reinforced supply hose of at least 1/2 inch (13 mm) and 7.5 m (about 25 ft) long, with a standard quick coupling; check the value for your model.
  5. Unroll the hose completely, with no loops or kinks.
  6. Remove the Aquastop coupling (a coupling that shuts off the water when it is disconnected) if it is fitted on the machine’s water inlet: it damages the pump.

Start the machine again. If the water supply was the problem, pressure builds within 2 minutes and the jet stays steady.

nettoyeur-haute-pression-plus-de-pression-1-1024x576 Pressure washer losing pressure: what should you check?
Tap fully open and hose unrolled: pressure should build within 2 minutes.

Good to know: the Aquastop coupling is still allowed on the tap side. If you draw water from a tank, the K5 manual limits the suction height to 0.5 m (about 1.6 ft).

Solution 2: bleed the air from the pump

Air in the machine stops the pressure from building and makes the pump vibrate. Bleeding clears that air out.

Advertisement
  1. Release the pressure as described in “Before you start”.
  2. Remove the lance from the spray gun.
  3. Open the tap, plug the machine back in and switch it on, without the lance.
  4. Squeeze the trigger until the water comes out without bubbles, for 2 minutes at most.
  5. Refit the lance.

The water should flow continuously, with no bubbles, and the pump should no longer vibrate.

Good to know: on professional Kärcher HD models, the manual says to unscrew the nozzle rather than remove the lance, then let the machine run until the water from the lance comes out without bubbles before screwing the nozzle back on.

Solution 3: clean the water inlet filter

The inlet filter is a small strainer sitting in the machine’s water inlet: it catches debris. Once clogged, it stops the pressure from building.

  1. Release the pressure and unplug the machine.
  2. Unscrew the coupling from the machine’s water inlet.
  3. Pull out the strainer with flat pliers.
  4. Rinse it under running water.
  5. Check that it isn’t damaged.
  6. Put the strainer back in place.
  7. Screw the coupling back onto the water inlet.

Plug the machine back in and switch it on: pressure should build normally if the strainer was the culprit.

Tip: Kärcher sells a water filter (part number 4.730-059) that protects the pump from impurities in the water.

If your strainer is damaged or your mains water carries sand, here is a water filter that screws onto the water inlet.

nettoyeur-haute-pression-plus-de-pression-300x169 Pressure washer losing pressure: what should you check?

Kärcher water filter for pressure washers

Catches sand and impurities in the water before they reach the pump. It screws onto the water inlet and can be rinsed.

Solution 4: clear the nozzle and check the lance

A clogged nozzle makes the pressure fluctuate. A worn or wrong-sized one keeps it from building.

  1. Release the pressure and unplug the machine.
  2. Clear the nozzle orifice with a pin.
  3. Flush the nozzle with water from the front.
  4. Replace the nozzle if it stays clogged or if it is worn.
  5. Check that the fitted nozzle is the one made for your machine: a wrong-sized nozzle gives no pressure.
  6. If your lance is a Vario Power type set to MIX while you aren’t spraying detergent, switch it back to high pressure: the manuals we consulted don’t confirm the effect on pressure, so check on your model.

The jet should become steady and strong again in the high-pressure position.

Good to know: the manuals we consulted only say that, on Vario Power lances, detergent is drawn in only in the MIX position. They don’t confirm that a lance left in the detergent or low-pressure position gives a weaker jet.

Solution 5: look for leaks

According to the manual of a professional Kärcher model, a leak or a blockage on the water supply side makes the pump vibrate and stops pressure from building. On the high-pressure side, a small leak is normal.

  1. Release the pressure and unplug the machine.
  2. Check the couplings and lines between the tap and the pump.
  3. Assess any leak on the high-pressure side: a small leak is normal, and the manual of a professional model tolerates up to 3 drops per minute.
  4. Hand the machine to an authorized service center if the leak is significant.

With no significant leak, the machine should build pressure once the water supply, strainer and nozzle have been checked.

Good to know: the manuals we consulted describe neither how to check the high-pressure hose nor how to replace an O-ring (a round rubber seal) or the hose. Follow your model’s manual or ask the service center.

If nothing works

Stop if the pressure still won’t build after checking the water supply, the air, the strainer and the nozzle, if the leak is significant, or if the motor hums without the pump delivering water. The manuals give no procedure for the pump or the valves: contact the brand’s authorized service center, or the seller if the machine is under warranty. An old entry-level machine is often replaced rather than repaired.

If the repair would cost more than the machine is worth, here are three 130 bar pressure washers to compare.

  • Kärcher K 4 Classic pressure washer, 130 bar130 bar, 420 l/h washer supplied with hose, gun, Vario Power lance and Dirt Blaster. A versatile machine for home and garden.AmazonSee at Amazon
  • Bosch UniversalAquatak 130 pressure washer130 bar, 1700 W washer with a self-priming pump that can draw water from a tank. Supplied with two nozzles and a 6 m hose.AmazonSee at Amazon
  • Nilfisk Core 130 pressure washer with power dimmer130 bar, 1500 W washer whose pressure is set on the machine. Supplied with a rotating lance and a 6 m hose.AmazonSee at Amazon

For that contact, have the model reference, the serial number from the rating plate and the purchase date ready.

A machine that wasn’t drained properly before winter can be damaged by frost. To avoid that failure, drain it before putting it away:

  1. Shut off the water supply.
  2. Disconnect the supply hose and the spray gun.
  3. Run the machine for 1 minute at most, until no more water comes out.
  4. Set the switch to 0/OFF.
  5. Store the machine somewhere frost-free.

The short dry run in step 3 is the only case where the manual allows the machine to run without water.

nettoyeur-haute-pression-plus-de-pression-2-1024x576 Pressure washer losing pressure: what should you check?
Drain the machine before winter: frost can damage it.

For your other garden machines, see also our guides on the lawn mower that won’t start and the hedge trimmer that won’t start.

Take better care of your pressure washer: our toolbox

These accessories replace wear parts and make routine upkeep of the machine easier.

  • Kärcher water filter for pressure washersCatches sand and impurities in the water before they reach the pump. It screws onto the water inlet and can be rinsed.AmazonSee at Amazon
  • Kärcher PremiumFlex anti-twist high-pressure hose, 10 m (K2 to K7)Replacement 10 m hose with an anti-twist system and Quick Connect fitting. It replaces a pierced, kinked or worn hose.AmazonSee at Amazon
  • Kärcher Dirt Blaster rotary lance for K2 to K4Rotary-jet lance for stubborn dirt. It replaces a worn or lost lance on K2 to K4 models.AmazonSee at Amazon
  • Kärcher gasket kit for pressure washers (41008320)Assortment of spare gaskets for Kärcher pressure washers. Useful to replace a worn connector seal.AmazonSee at Amazon
  • Kärcher Plug and Clean universal cleaner, 1 LReady-to-use universal cleaner drawn in by the pressure washer. It loosens everyday dirt without scrubbing.AmazonSee at Amazon

Frequently asked questions

Why has my pressure washer lost pressure?

Kärcher manuals name three causes: too little incoming water, a clogged inlet filter, or air in the machine. A clogged or worn nozzle can also be to blame. Start by opening the tap fully and checking the supply hose.

How do I bleed the air from a pressure washer?

Remove the lance, switch the machine on and squeeze the trigger until the water comes out without bubbles, for 2 minutes at most. Then refit the lance. On professional Kärcher HD models, it’s the nozzle that you unscrew.

How do I unclog a pressure washer nozzle?

With the machine depressurized and unplugged, clear the nozzle orifice with a pin. Then flush it with water from the front. If it stays clogged or is worn, replace it.

Why does my Kärcher pulse or surge?

Fluctuating pressure comes from a clogged nozzle or an insufficient water flow, according to the manual. Clean the nozzle and check that the tap supplies the flow required: 8 l/min for a K2 and 10 l/min for a K5. Air in the pump also makes it vibrate: bleed it.

How do I protect a pressure washer from frost?

Drain it before winter: water supply shut off, hose and spray gun disconnected, then run it for 1 minute at most until no more water comes out. Then store it somewhere frost-free. The K2 manual also forbids using it below 0 °C (32 °F).

Share this content:

Leave a Reply

Your email address will not be published. Required fields are marked *