Advertisement
Farm and garden equipment

Leaf blower won’t start: what to check before the repair shop?

Gas leaf blower won't start or stalls right away? Check the starting procedure, fuel, flooded engine, spark plug and filters, in that order.

6 min read

Broken-down gas garden machine with a warning sign, a repair wrench and dead leaves
Table of contents
  1. Common symptoms and causes
  2. Before you start
  3. Solution 1: follow the right starting procedure
  4. Solution 2: replace old or badly mixed fuel
  5. Solution 3: clear a flooded engine
  6. Solution 4: check, clean or replace the spark plug
  7. Solution 5: clean the filters and the spark arrestor
  8. If nothing works and the blower still won’t start
  9. Take better care of your leaf blower: our toolbox
  10. Frequently asked questions
    1. Why won’t my gas leaf blower start?
    2. How do I clear a flooded leaf blower?
    3. Why won’t my leaf blower start when it’s hot?
    4. What fuel mix goes in a 2-stroke leaf blower?

This article contains affiliate links: if you buy through them, Wanda-techs earns a commission at no extra cost to you.

When a leaf blower won’t start, the cause is usually something you can fix without a shop: the starting procedure, old fuel, a flooded engine or a fouled spark plug. Husqvarna lists starting mistakes among the most common causes, so begin there.

Advertisement

Common symptoms and causes

  • The pull cord turns but the engine gives no sign of firing: stop switch off, too little priming or a faulty spark plug.
  • The engine starts, then stalls: old fuel, a dirty air filter or a clogged spark arrestor.
  • The blower won’t start when hot: choke left closed on an engine that is already warm.
  • The spark plug is wet after several pulls: a flooded engine, according to user reports.
  • The engine cuts out when you tilt the blower: clogged fuel filter or fuel line.
  • Nothing works after all the checks: the carburetor needs to be inspected.

Before you start

Stop the engine, remove the key if it has one and wait until the impeller has stopped completely before touching anything. Let the engine cool down. Disconnect the spark plug boot before you work on the plug, the filters or the exhaust.

Warning: gasoline is flammable. Work outdoors, away from any flame, with a cold engine, and never run the blower in a closed room.

Warning: opening the machine may void the warranty, so check when it ends first. Adjusting the carburetor, or using gasoline and oil the manufacturer does not approve, can void it too.

Get a spark plug wrench, a feeler gauge, a wire brush, a can for the old fuel and some fresh mix. Keep the manual within reach. Controls differ between brands: choke lever or knob, with or without a primer bulb.

Solution 1: follow the right starting procedure

Husqvarna points to four common mistakes: too little priming, the choke closed on a warm engine, the stop switch left off and pulls that are too weak. The procedure below is Husqvarna’s. The position names may differ on your model.

  1. Set the blower on the ground outdoors, in a clear area.
  2. Move the stop switch to the run position (ON).
  3. Press the primer bulb at least 10 times, until it fills with fuel.
  4. With a cold engine, set the choke to the closed position (FULL).
  5. Hold the blower firmly on the ground and pull the starter cord with one sharp stroke until you hear a short “pop”, the first sign of ignition.
  6. Move the choke from FULL to the run position (RUN).
  7. Pull the cord again until the engine starts, then let it idle for a few moments.
  8. With a warm engine, leave the choke on HALF or RUN, never on FULL, then pull the cord until it starts.

The engine should start and hold an idle without stalling. If it still won’t start after more than 3 pulls with the choke closed, go to solution 3: according to Stihl (a brush cutter source), the engine is probably flooded.

Advertisement

Tip: first pull gently until you feel the cord resist, then give a sharp stroke. It spares the cord and the pull is more effective.

Solution 2: replace old or badly mixed fuel

Old or badly mixed fuel clogs the fuel system. Stihl recommends never using a mix more than 60 days old in its blowers. Another manual from the brand says 30 days: go with the shorter period.

Good to know: the mix ratio varies by manufacturer. According to Stihl, most of its machines run on a 50:1 mix (50 parts gasoline to 1 part 2-stroke oil) with unleaded gasoline. Always check the ratio shown on your machine.

  1. Empty the fuel tank.
  2. Read the mix ratio on the fuel cap or in the manual.
  3. Prepare a fresh mix of unleaded gasoline and 2-stroke oil at that ratio.
  4. Fill the tank with the fresh mix.
  5. Restart the engine with the procedure from solution 1.

The engine should start after a few pulls and rev up smoothly. Afterward, don’t let the tank run dry.

souffleur-ne-demarre-pas-1-1024x576 Leaf blower won't start: what to check before the repair shop?
A fresh mix at the right ratio fixes a good share of hard starts.

Tip: if you rarely use the blower, an ethanol-free ready-to-use mix keeps longer. Stihl claims up to 2 years after opening for its US product, and up to 5 years in its European manual.

If you would rather stop mixing fuel yourself, here is a ready-to-use 2-stroke fuel.

Advertisement
souffleur-ne-demarre-pas-300x169 Leaf blower won't start: what to check before the repair shop?

Stihl MotoMix ready-mixed 2-stroke fuel

Alkylate fuel already mixed with 2-stroke oil at 1:50. It avoids mixing mistakes and keeps better than ordinary petrol.

Solution 3: clear a flooded engine

A flooded engine has received too much fuel to ignite. No Husqvarna or Stihl page on blowers describes a procedure: the method below comes from Stihl’s FAQ for brush cutters, whose engine is comparable. Stihl also advises moving the choke out of the closed position after 3 or 4 pulls.

  1. Move the choke out of the closed position.
  2. Let the blower sit for 20 to 30 minutes.
  3. Pull the starter cord several times, with the choke out of the closed position.

The engine should start after a few pulls. If not, remove the spark plug (solution 4). According to user reports, a wet spark plug points to a flooded engine.

On some Stihl models, the manual tells you to leave the choke in a specific position and keep pulling the cord. That position depends on the model. Follow your machine’s manual if it describes one.

Solution 4: check, clean or replace the spark plug

A dirty, worn or badly gapped spark plug often prevents starting. The electrode gap depends on the model: read the value in the manual.

  1. Disconnect the spark plug boot, the cap attached to the plug wire.
  2. Unscrew the spark plug with a spark plug wrench.
  3. Examine the porcelain insulator and the electrodes: dirt, cracks, a burnt electrode.
  4. Clean a dirty but intact plug, and replace a cracked or burnt one.
  5. Slide a feeler gauge between the two electrodes to check the gap.
  6. If the gauge is too tight or too loose, bend the outer electrode slightly, and nothing else.
  7. Refit the spark plug, then reconnect the boot.

The gauge should slide between the electrodes with slight drag. The engine should then start with the procedure from solution 1.

If you can’t find your plug with the tool that came with the blower, here is a spark plug wrench.

souffleur-ne-demarre-pas-300x169 Leaf blower won't start: what to check before the repair shop?

AEG spark plug wrench, 3 sockets 14-16-21 mm

Spark plug wrench with three socket sizes. It removes and refits plugs without damaging the insulator.

souffleur-ne-demarre-pas-2-1024x576 Leaf blower won't start: what to check before the repair shop?
With the plug out, check the insulator, the electrodes and the gap given in the manual.

Tip: according to user reports, a spark tester lets you check that a spark is present. Spark plug wet after several pulls? Go back to solution 3.

Solution 5: clean the filters and the spark arrestor

A dirty air filter restricts the air coming in. A spark arrestor covered in carbon slows the exhaust gases and makes the engine stall.

  1. Remove the air filter.
  2. Clean the filter if it is dirty, replace it if it is damaged, then refit it.
  3. Inspect the fuel lines (hoses) and the fuel filter in the tank: clog, crack, pinched hose.
  4. Replace the damaged fuel filter or fuel line.
  5. With a cold engine and the spark plug boot disconnected, remove the spark arrestor from the exhaust.
  6. Brush off the carbon (the black combustion deposit) with a wire brush.
  7. Replace the spark arrestor if it stays clogged after brushing, then refit it.

The engine should start, hold its speed at full throttle and no longer cut out when you tilt the blower.

If nothing works and the blower still won’t start

Stop if the blower still refuses to start with a fresh mix, the right procedure, a clean and correctly gapped spark plug, and clean filters and spark arrestor. The carburetor then needs to be inspected. That job belongs to a brand-authorized shop, especially since it can affect the warranty.

According to Stihl user forums, with no official confirmation, the carburetor diaphragm or needle and an air leak at the crankcase are possible leads. The diagnosis is the shop’s to make.

Bring the model number, the fuel you used and the spark plug you removed, as it came out. For the same approach on other machines, see our guides on a chainsaw that won’t start, a brush cutter that won’t start and a lawn mower that won’t start.

Take better care of your leaf blower: our toolbox

Quality 2-stroke oil, a clean fuel can, a fuel stabiliser and hand and eye protection help prevent the next breakdown.

  • Stihl HP Super 2-stroke oil, 1 litreSemi-synthetic 2-stroke engine oil, JASO FD class, used at a 1:50 ratio. The bottle with a measuring chamber makes mixing easier.AmazonSee at Amazon
  • Valpro 5 L steel petrol jerry canFive-litre metal can with a safety pin, suitable for all fuels. Use it to drain the old petrol from the mower and to store the fresh petrol.AmazonSee at Amazon
  • STA-BIL fuel stabilizer for petrol enginesAdditive to pour into fresh petrol to protect it from ageing while the machine is stored. It helps the engine start easily again in spring.AmazonSee at Amazon
  • Mechanix Wear Original Covert mechanic glovesClose-fitting work gloves that protect the hands during car jobs. They keep a good grip on tools and parts.AmazonSee at Amazon
  • 3M Command 2890SC safety gogglesGoggles that protect the eyes from splashes and dust. Useful when sanding, polishing or handling solvents.AmazonSee at Amazon

Frequently asked questions

Why won’t my gas leaf blower start?

Most often the stop switch was left off, the priming is insufficient, the choke is in the wrong position or the fuel is too old. Next come a flooded engine, a fouled spark plug, and a clogged air filter or spark arrestor. If all of that checks out, have the carburetor inspected at a shop.

How do I clear a flooded leaf blower?

Move the choke out of the closed position, let the blower sit for 20 to 30 minutes, then pull the starter cord again. This method comes from Stihl for its brush cutters: no official procedure specific to blowers was found. If the engine still won’t start, check the spark plug (solution 4).

Why won’t my leaf blower start when it’s hot?

The choke is probably in the closed position. On a warm engine, Husqvarna says to set it to HALF or RUN, never FULL. If the engine was flooded by pulls with the choke closed, apply solution 3.

What fuel mix goes in a 2-stroke leaf blower?

The ratio shown on the fuel cap or in the manual, because it varies by manufacturer. According to Stihl, most of its machines run at 50:1 with unleaded gasoline. Prepare a fresh mix and don’t keep it more than 30 days, unless it is a ready-to-use mix.

Share this content:

Leave a Reply

Your email address will not be published. Required fields are marked *