Advertisement
Home appliances and smart home

Netatmo Thermostat Offline: How Do You Reconnect It Again?

Relay not reachable or thermostat not reachable: the lost link is either the Relay's connection to your router or the thermostat's connection to the Relay. Here are Netatmo's fixes, from the simplest to the most advanced.

5 min read

Wall thermostat and Internet router joined by a broken chain, Wi-Fi signal cut
Table of contents
  1. Common symptoms and causes
  2. Before you start
  3. Solution 1: Restart the router, then the Relay
  4. Solution 2: Check the Relay’s power supply
  5. Solution 3: Reconnect the Netatmo Relay to Wi-Fi after changing your router
    1. With Netatmo Energy
    2. With Home + Control
    3. If the setup fails
  6. Solution 4: Netatmo thermostat no longer connects to the Relay
    1. Replace the Netatmo thermostat batteries
    2. Move the thermostat and the Relay closer
  7. Solution 5: Adjust your router settings
  8. If nothing works
  9. Take better care of your Netatmo thermostat: our toolbox
  10. Frequently asked questions
    1. Does the Netatmo thermostat work without Internet?
    2. How do I reconnect Netatmo to Wi-Fi after changing my router?
    3. When should I change the Netatmo thermostat batteries?
    4. What does the Netatmo Relay light mean?

This article contains affiliate links: if you buy through them, Wanda-techs earns a commission at no extra cost to you.

When the app shows your Netatmo thermostat offline, either the Relay has lost the Wi-Fi connection to your router, or the thermostat has lost its radio link to the Relay. Netatmo lists the usual causes: a badly powered Relay, a weak or interrupted Internet connection, a changed Wi-Fi password, or a newly added Wi-Fi extender.

Advertisement

While the Internet is down, the thermostat keeps following its schedule.

Common symptoms and causes

  • Netatmo Energy shows “Relay not reachable”, or Home + Control shows a red banner reading “[Relay name] is unreachable”: the problem sits between the Relay and your router (solutions 1, 2, 3 and 5).
  • The app shows “Thermostat not reachable”, the thermostat screen displays an “!” logo or stays frozen on its last reading: the thermostat has lost the radio link with the Relay (solution 4).
  • The screen shows the “Searching for the Relay” logo: the thermostat cannot find the Relay, which is out of range or not paired.
  • A low-battery logo appears next to the temperatures.

The Relay is the module that connects to your router over Wi-Fi. The thermostat only talks to the Relay, over a secured long-range radio link.

Before you start

  • Identify your app: Netatmo Energy manages the Smart Thermostat and the Relays of the Starter Packs; Home + Control manages every Relay, including the one of the Smart Modulating Thermostat.
  • Grab a smartphone with Bluetooth and location (GPS) turned on, to reconfigure the Wi-Fi.
  • Check that your router broadcasts a personal 2.4 GHz Wi-Fi network with WPA2 encryption: the Relay does not work on a public network.
  • Keep 3 new 1.5 V AAA (LR03) alkaline batteries within reach.

Warning: if your Relay is connected to the boiler, do not touch the wires of its adapter or the boiler wiring. The wires of this adapter are linked to mains power. Leave any check to a heating engineer.

Warning: use new AAA alkaline batteries (non-rechargeable lithium batteries are also accepted), never rechargeable ones, and respect the polarity. Remove any battery that has leaked and clean the corrosion with white vinegar.

Warning: do not uninstall the Relay from the app and do not reset it. Uninstalling erases the history, settings and schedules; resetting erases the Relay’s Wi-Fi and HomeKit credentials.

Good to know: Netatmo states that a reset is not necessary after a Wi-Fi loss.

Advertisement

Solution 1: Restart the router, then the Relay

  1. Unplug your Internet router.
  2. Unplug the Relay.
  3. Plug the router back in.
  4. Wait until the Internet connection is back.
  5. Plug the Relay back in.

When you plug it in, the Relay’s light should blink quickly 5 times. The Relay can take a few minutes to reconnect, and the thermostat up to 15 minutes to sync with it again.

Wait that long before moving on.

netatmo-thermostat-hors-ligne-1-1024x576 Netatmo Thermostat Offline: How Do You Reconnect It Again?
Plug the router back in first, then the Relay once the Internet is back.

Solution 2: Check the Relay’s power supply

The light does not blink 5 times when you plug it in? Check the power supply.

  1. Unplug the Relay from its mains adapter or its boiler adapter.
  2. Wait 10 seconds.
  3. Plug the Relay back in.
  4. Check that the light blinks quickly 5 times.
  5. If there is no light and you use a mains adapter, plug the adapter into another socket.
  6. On a mains adapter, look at the condition of the adapter’s pins.
  7. On a mains adapter, push the adapter in until it clicks.
  8. For a temporary test, power the Relay through its micro-USB port, with a phone charger or a computer.

The light should blink quickly 5 times.

Warning: Relay on a boiler adapter and no light? Do not open the adapter and do not touch the wires: call a heating engineer.

Solution 3: Reconnect the Netatmo Relay to Wi-Fi after changing your router

After a change of Wi-Fi network, a new password or an added extender, Netatmo asks you to rerun the Wi-Fi setup from the error message in the app. No Relay reset is needed.

Advertisement

With Netatmo Energy

  1. Open Netatmo Energy and select the home where the Relay is.
  2. On the error screen, tap Configure your Wi-Fi.
  3. Follow the instructions in the app.

No error screen? Go through Settings > Manage my home > [Relay name] > Configure your Wi-Fi.

With Home + Control

  1. Open Home + Control and select the home where the Relay is.
  2. Tap the red banner, then Wi-Fi configuration.

The same setting is in Settings > Manage my home > [Relay room] > [Relay name] > Configure network.

If the setup fails

  1. Restart your smartphone.
  2. Turn on the phone’s Bluetooth and location (GPS).
  3. Run the Wi-Fi setup again.

The app should show the Relay again, without the “Relay not reachable” message.

Solution 4: Netatmo thermostat no longer connects to the Relay

Replace the Netatmo thermostat batteries

A thermostat with low batteries still works. With empty batteries, it can no longer be controlled or command the boiler.

  1. Remove the batteries from the thermostat.
  2. Check that none has leaked.
  3. Clean any corrosion with a cotton swab dipped in white vinegar.
  4. Insert 3 new, in-date 1.5 V AAA (LR03) alkaline batteries, respecting the polarity.
  5. Wait until the screen shows the temperatures: the “Searching for the Relay” logo blinks first, for a few minutes.
  6. Press the + and – buttons to test the thermostat.

The thermostat should display the temperatures and react to the buttons.

To replace them, here are alkaline AAA (LR03) batteries in a large pack.

netatmo-thermostat-hors-ligne-300x169 Netatmo Thermostat Offline: How Do You Reconnect It Again?

Duracell Plus AAA (LR03) alkaline batteries, pack of 24

1.5 V alkaline AAA batteries for remote controls, thermostats and other low-drain devices. The large pack covers several changes.

Move the thermostat and the Relay closer

The thermostat still says “not reachable”? Play with the radio range: 100 m in open field by design, but 10 to 20 m indoors. Reinforced concrete, stone and metal cut it sharply; drywall and wood much less.

  1. Move the Relay closer to the thermostat.
  2. Test both devices in the same room.
  3. Change the orientation of the Relay or the thermostat.
  4. Keep them more than 50 cm (20 in) from other electrical devices, and at least 10 cm (4 in) from each other.
  5. Take them out of spots that interfere with radio: behind the boiler casing or a stove, behind a TV, near an aquarium, on or inside metal, in a closed cabinet, near several cables.

The “!” or “Searching for the Relay” logo should disappear from the screen. If your Relay is fixed to the boiler adapter, do not touch the wiring to move it: ask a heating engineer.

netatmo-thermostat-hors-ligne-2-1024x576 Netatmo Thermostat Offline: How Do You Reconnect It Again?
New batteries and a closer Relay: the thermostat finds its radio link again.

Good to know: if “Searching for the Relay” persists, the thermostat may no longer be paired. We could not verify the pairing procedure on an official page: ask Netatmo support for it.

Solution 5: Adjust your router settings

Netatmo points to its network guide, shared by all its products, in two cases. The light blinks but the Relay is not connected after 10 minutes, or it disconnects several times a day.

Warning: after changing the network name (SSID) or the Wi-Fi password (steps 2 and 4), the Relay will need to be reconfigured with Solution 3.

  1. Restart the router.
  2. If you use an extender or an extra access point, give each access point a different network name (SSID).
  3. Keep WPA2 enabled, including on a WPA3 router (mixed WPA2/WPA3 mode).
  4. Choose a simpler Wi-Fi password, without special characters.
  5. Turn off MAC address filtering (each device’s hardware identifier), or allow the Relay.
  6. Turn off parental controls and access restrictions.
  7. If the Relay disconnects every day at the same time, turn off the router’s sleep mode.
  8. Set the Wi-Fi channel to automatic, or to channel 1, 6 or 11.
  9. Update the router’s firmware.
  10. If a firewall is active, open UDP ports 500 and 4500.
  11. In that case, give the Relay a fixed IP address tied to its MAC address.
  12. If the Wi-Fi signal is weak where the Relay sits, install a Wi-Fi extender in the room.

The Relay should stay connected without repeated drops. After adding an extender, redo Solution 3 too.

If the signal is weak at the Relay’s spot, here is a dual-band Wi-Fi extender to compare.

netatmo-thermostat-hors-ligne-300x169 Netatmo Thermostat Offline: How Do You Reconnect It Again?

TP-Link RE315 AC1200 dual-band Wi-Fi repeater

Extends the Wi-Fi signal into a room the router reaches poorly. Dual-band, it works on 2.4 GHz and 5 GHz.

If nothing works

Stop if the Relay’s light never blinks after the power checks. Same if the Relay stays offline after the Wi-Fi reconfiguration and the network guide: contact Netatmo support and check your warranty.

A boiler failure or any doubt about the wiring is a job for a heating engineer. If it is your electric radiators that no longer heat, see our guide on an electric heater that won’t heat; for another Wi-Fi device, the one on a printer showing offline.

Take better care of your Netatmo thermostat: our toolbox

Spare batteries, better Wi-Fi coverage, a replacement thermostat: what it takes to keep your connected heating online.

  • Energizer Ultimate Lithium AAA (L92) batteries, pack of 41.5 V non-rechargeable lithium AAA batteries for devices that run for a long time on batteries. They cope well with temperature extremes and keep well in storage.AmazonSee at Amazon
  • TP-Link Deco X20 (pack of 2) Wi-Fi 6 mesh system AX1800Two units that cover a home with a single Wi-Fi network. Useful when one router cannot reach every room.AmazonSee at Amazon
  • Netatmo Smart Thermostat for individual boilers (NTH01-FR-EC)Wireless connected thermostat with a Relay, controlled from a smartphone app. It works with most individual boilers.AmazonSee at Amazon
  • Netatmo ORIGINAL smart thermostat for individual heating (wireless or wired kit)Connected thermostat from the Netatmo Original range, sold as a wireless or wired kit. It is controlled from the app for individual heating.AmazonSee at Amazon

Frequently asked questions

Does the Netatmo thermostat work without Internet?

Yes: it keeps heating according to the current week’s schedule or the last setpoint, like the connected valves. Remote control, schedule edits and Auto-Adapt anticipation are unavailable. The buttons still set a manual setpoint, for the duration defined in Operating mode > Default duration of manual setpoints (3 h by default).

How do I reconnect Netatmo to Wi-Fi after changing my router?

Rerun the Relay’s Wi-Fi setup from the app (Solution 3), without uninstalling or resetting it. The new router must broadcast a personal 2.4 GHz Wi-Fi network with WPA2.

When should I change the Netatmo thermostat batteries?

Within 4 weeks of the low-battery logo appearing next to the temperatures, which the app also reports. Avoid rechargeable batteries: their voltage is too low.

What does the Netatmo Relay light mean?

When you plug it in, the Relay’s light should blink quickly 5 times. If there is no light, check the power supply (Solution 2). If it blinks but the Relay is not connected after 10 minutes, go to Solution 5.

Share this content:

Leave a Reply

Your email address will not be published. Required fields are marked *