Advertisement
Farm and garden equipment

Chainsaw Chain Not Spinning? What to Check and How to Fix It

Your chainsaw engine runs but the chain stays still? Chain brake, tension, bar, lubrication, clutch or battery: the checks in order, from the simplest to the most technical.

5 min read

Gear and broken chain next to a warning sign and a repair wrench
Table of contents
  1. Common symptoms and causes
  2. Before you start
  3. Solution 1: release the chain brake
  4. Solution 2: adjust a chain that is too tight or stuck
  5. Solution 3: clean the bar and check the lubrication
  6. Solution 4: check the clutch on a gas chainsaw
  7. Solution 5: battery chainsaw that won’t start
  8. If nothing works
  9. Gear up to maintain your chainsaw: our toolbox
  10. Frequently asked questions
    1. Why does the engine run but the chain doesn’t spin?
    2. How can I tell if the chain brake is engaged?
    3. Can an over-tight chain jam?
    4. Can a chainsaw clutch fail?

This article contains affiliate links: if you buy through them, Wanda-techs earns a commission at no extra cost to you.

Chainsaw chain not spinning while the engine revs? Most often the chain brake is engaged, then, according to Husqvarna, a jammed chain, poor lubrication, an over-tight chain and, last, a worn clutch. Start with the brake; solution 5 applies only to battery chainsaws.

Advertisement

Common symptoms and causes

  • The engine runs but the chain stays still: chain brake engaged, chain too tight, bar nose sprocket seized or clutch worn.
  • The chain is hard to pull by hand: too much tension, not enough oil, or sawdust in the bar groove (the channel the chain links slide in).
  • The chain is stuck in the wood: it is pinched in the cut.
  • An electric or battery chainsaw won’t start or cuts out: battery too hot or too cold, overload protection tripped by an over-tight chain, or brake engaged.

Gas engine won’t start at all? The problem lies elsewhere: follow our checks for a chainsaw that won’t start instead.

Before you start

  • Stop the engine, remove the key or the battery, and wait until the chain has fully stopped before doing anything.
  • On a gas chainsaw, also disconnect the spark plug cap before touching the chain, bar or sprocket.
  • Wear cut-resistant gloves to handle the chain and its teeth.
  • After use, let the machine cool: the chain, bar and sprocket can be hot.
  • Keep your model’s manual within reach. The direction to release the brake and the right chain tension depend on it.

Warning: on a battery chainsaw, remove the battery before touching the chain; with Stihl, engage the chain brake before removing it. Never puncture, bend or heat a lithium battery; a swollen battery can no longer be recharged and goes to a collection point; work on a non-flammable surface.

Warning: opening the machine may void the warranty, so check the warranty end date first. Leave the clutch and chain brake to an authorized workshop. And never run the engine with the brake engaged: it damages the clutch.

Solution 1: release the chain brake

The chain brake locks the chain. It engages when the front hand guard is pushed forward, and by itself during kickback.

Warning: do not rev the engine while the brake is engaged. According to Stihl, revving with the brake on damages the clutch and the brake within moments.

  1. With the engine off, look at the position of the front hand guard: pushed forward, it means the brake is engaged.
  2. Pull the hand guard back toward you, toward the front handle, to release the brake. This direction applies to most models but varies, so check your manual.
  3. Start the chainsaw with the chain clear of any cut.
  4. Squeeze the throttle.

The chain should start spinning as soon as you accelerate.

Advertisement
chaine-tronconneuse-ne-tourne-pas-1-1024x576 Chainsaw Chain Not Spinning? What to Check and How to Fix It
Hand guard pushed forward: the brake is engaged and the chain cannot spin.

Tip: check the front hand guard before taking anything apart. It is the most common cause, and the only one you can fix without tools.

Solution 2: adjust a chain that is too tight or stuck

An over-tight chain can no longer travel around the bar. On an electric or battery chainsaw, this friction can also trip the overload protection and cut the motor.

Chain pinched in a cut? Stop the engine, remove the key or the battery, put on cut-resistant gloves, then free it. Never restart the chainsaw with the chain engaged in the wood.

The exact procedure and the tension to aim for depend on the model. Your chainsaw’s manual takes priority.

  1. Make the machine safe: engine off and key removed, spark plug cap disconnected on a gas saw or battery removed, chain stopped and cooled, cut-resistant gloves on.
  2. Find your model’s tensioner in the manual: tension screw or side tensioner.
  3. Retension the chain following the procedure and tension given in the manual.

Once retensioned, the chain should spin when you accelerate.

Good to know: some models, such as the Stihl MS 193 T, have a side tensioner. A new chain needs retensioning more often than a worn one. Check the tension regularly.

Advertisement

Solution 3: clean the bar and check the lubrication

Sawdust, chips and dirt can jam the chain or the bar nose sprocket, the small toothed wheel at the tip of the bar. A lack of chain oil increases friction. Husqvarna also lists unsuitable oil or too much oil.

  1. Make the machine safe: engine off and key removed, spark plug cap disconnected on a gas saw or battery removed, chain stopped and cooled, cut-resistant gloves on.
  2. Remove the cover and the bar nuts.
  3. Look for sawdust, chips or dirt on the chain and in the bar groove, and remove them.
  4. Spray resin solvent on the bar nose sprocket.
  5. Check the chain oil supply: not too little, not too much, and the right kind of oil.
  6. On models that allow it, increase the oil pump flow.

After reassembly and setting the tension (solution 2), the chain should spin freely when you accelerate. Oil still not reaching the chain? Stihl recommends having the lubrication checked by an authorized dealer.

chaine-tronconneuse-ne-tourne-pas-2-1024x576 Chainsaw Chain Not Spinning? What to Check and How to Fix It
Clean bar groove and oil reaching the chain: the chain should spin freely.

Solution 4: check the clutch on a gas chainsaw

On a gas chainsaw, the clutch passes the engine’s motion to the drum that carries the chain sprocket. Once worn, its shoes no longer drive the drum.

  1. Make sure the chain brake is released.
  2. Start the chainsaw with the chain clear of any cut.
  3. Open the throttle fully.
  4. If the engine revs and the chain stays still, release the throttle and stop the engine.
  5. Have the clutch assembly replaced by an authorized workshop.

After the clutch is replaced, the chain should spin as soon as you accelerate.

Warning: during the test, keep your hands away from the chain. Do not touch the chain, bar or sprocket until the engine has stopped, the spark plug cap is disconnected and the parts have cooled.

Good to know: the opposite symptom, a chain that creeps at idle, comes from a worn clutch spring. The chain brake also wears through friction, so have it checked at the same time.

Solution 5: battery chainsaw that won’t start

A battery chainsaw refuses to start when the battery is too hot or too cold, or when the machine has overheated. The lights signal it. Their meaning changes from one model to another: the manual takes priority.

  1. Look at the lights on the battery and on the chainsaw, and read what they mean in the manual.
  2. If the battery or the machine is too hot or too cold, let it return to normal temperature.
  3. Engage the chain brake.
  4. Remove the battery, then put it back in.
  5. Release the chain brake.
  6. Switch the chainsaw on.

The chain should spin when you squeeze the trigger. If the manual lists a fault light, move on to the next section.

If nothing works

Brake released, tension right, groove clean, oil flowing, and the chain still won’t spin? Stop there. The same goes for a worn clutch or sprocket, or a fault light on a battery machine.

Take the chainsaw to an authorized workshop for the brand (Stihl, Husqvarna or other). Have the model and a description of the symptom ready: engine revving without driving the chain, jammed chain, lights on.

Are your other gas machines giving you trouble too? See our checks for a brushcutter that won’t start.

Gear up to maintain your chainsaw: our toolbox

The right gloves, eyewear and fuel make chainsaw maintenance safer and more regular.

  • Oregon chainsaw protective glovesGloves with cut protection for chainsaw work. They go with eye and hearing protection.AmazonSee at Amazon
  • 3M Command 2890SC safety gogglesGoggles that protect the eyes from splashes and dust. Useful when sanding, polishing or handling solvents.AmazonSee at Amazon
  • Stihl HP Super 2-stroke oil, 1 litreSemi-synthetic 2-stroke engine oil, JASO FD class, used at a 1:50 ratio. The bottle with a measuring chamber makes mixing easier.AmazonSee at Amazon
  • Stihl MotoMix ready-mixed 2-stroke fuelAlkylate fuel already mixed with 2-stroke oil at 1:50. It avoids mixing mistakes and keeps better than ordinary petrol.AmazonSee at Amazon

Frequently asked questions

Why does the engine run but the chain doesn’t spin?

Most often the chain brake is engaged. Husqvarna then lists, in order, a chain jammed by sawdust or pinched in the wood, incorrect lubrication, an over-tight chain and a worn clutch.

How can I tell if the chain brake is engaged?

Look at the front hand guard: pushed forward, it engages the brake. The brake also trips by itself during kickback.

Can an over-tight chain jam?

Yes. When it is too tight, the chain can no longer travel around the bar and friction rises. On an electric or battery chainsaw, the overload protection can also cut the motor.

Can a chainsaw clutch fail?

Yes. Once worn, its shoes no longer drive the drum: the chain stays still at full throttle with the brake released. The clutch assembly then has to be replaced in a workshop.

Share this content:

Leave a Reply

Your email address will not be published. Required fields are marked *