This article contains affiliate links: if you buy through them, Wanda-techs earns a commission at no extra cost to you.
A PS5 controller drifts when your character, the camera or the cursor moves on its own while you are not touching the stick. According to unofficial sources, the most common cause is a worn stick sensor, a potentiometer that measures the stick’s position.
Start with the update and the reset. Neither needs any disassembly.
Common symptoms and causes
- The character, camera or cursor moves by itself while the stick is at rest.
- Wear of the stick sensor (potentiometer) on the standard DualSense, according to unofficial sources: a reset cannot fix physical wear.
- Dust or debris around the stick, according to unofficial sources.
- A software glitch, which resetting the controller can clear.
Tip: note right now which stick drifts, left or right. You will run the same test after each solution.
Before you start
Have a pin or an unfolded paper clip ready for the reset button. Keep the official USB cable that came with the controller within reach to pair it again.
Warning: opening the device may void the warranty, so check when your warranty ends first. Sony does not repair a controller that contains unofficial parts.
Warning: resetting the controller erases no data. If you send the console itself to Sony, it comes back restored to factory settings: back up your saves before shipping, or they will be lost.
Warning: on the DualSense Edge, discharge static electricity before handling a stick module and do not touch its connectors. This advice comes from the controller’s manual, according to the search results; the Sony page we read does not repeat it.
Solution 1: update the console and the controller
- Install the latest PS5 system software.
- On a DualSense Edge, also update the controller software by following Sony’s “Update controller software” guide.
Then relaunch a game and leave the stick at rest. The character and the camera should stay still.
Solution 2: reset the PS5 controller and pair it again over USB
Resetting erases no data. On the DualSense Edge, it changes neither the pairing nor the controller’s profiles.
- Turn off the PS5.
- Unplug the USB cable from the controller.
- Find the small hole on the back of the controller, next to the Sony logo.
- Push a pin into the hole and hold the button for at least 5 seconds.
- Connect the controller to the PS5 with the official USB cable that came with it.
- Press the PS button.
The controller should reconnect to the console. Test again in a game with the stick at rest: the character should stay still.

If the controller will not reconnect, follow our guide for a PS5 controller that won’t connect to the console.
Solution 3: adjust the dead zone in the game
The dead zone is the small range of stick movement that the game ignores. Sony’s official pages mention no dead zone setting in the console. It exists only in games that offer it.
- Open the game’s options, in the controls or controller section, and look for a dead zone setting.
- Increase the dead zone for the affected stick.
The character should stay still when you let go of the stick.
Good to know: this setting hides the drift in that game only. It does not repair the stick.
Solution 4: clean around the stick without taking it apart
Sony describes no cleaning procedure. The method below comes from unofficial sources.
- Unplug the USB cable from the controller.
- Lightly dampen a cotton swab with isopropyl alcohol.
- Run the swab around the base of the stick, without opening the controller.
- Let it dry completely before plugging the controller back in.
Plug the controller back in and test in a game with the stick at rest. Still drifting? Move on to the next solution or to the “If nothing works” section.
Solution 5: replace the stick module (DualSense Edge)
Only the DualSense Edge has replaceable stick modules. They are sold separately and fit on either the left or the right. The standard DualSense has none.
- Check that the player indicator is off; if not, hold the PS button until it goes off.
- Unplug the USB cable.
- Slide the RELEASE latch on the back of the controller.
- Remove the front cover.
- Raise the module’s release lever.
- Pull the old module out.
- Slide the new module along the grooves until it clicks, checking its orientation.
- Lower the release lever.
- Line up the cover’s tabs with the notches and press until it clicks.
The cover must be firmly clipped in. With the stick at rest, the character stays still.

If nothing works
Still drifting after the update, the reset and a test? Stop there. Do not open a standard DualSense that is under warranty.
- Open the PlayStation Repairs service at playstation.com/repairs and choose the “Button or analog stick issue” category.
- Contact PlayStation support to get a reference number, sent by email.
- Check that the controller’s model and serial number match those on the request.
- Follow the repair’s progress on the Repairs page.
Keep the controller’s serial number handy. Sony aims for 15 days after it receives the product. A repaired or replaced product is guaranteed for 3 months, or until the end of the original warranty if that lasts longer.
For a DualSense Edge, do not send the case or the USB cable. Remove the back buttons, paddles and caps, but leave the stick modules in place: Sony does not repair unofficial parts.
Out of warranty, a DualSense Edge is repaired by swapping the stick module (solution 5). With a standard DualSense, replacing the controller is what’s left.
If the repair isn’t worth it, here are two official controllers to compare: the standard DualSense and the DualSense Edge.
- Sony DualSense wireless controller for PS5, whiteThe official PS5 controller, with haptic feedback, adaptive triggers and a built-in microphone. It is the simplest replacement when the old one no longer holds a charge.AmazonSee at Amazon
- Sony DualSense Edge wireless controller for PS5A controller with customisable controls and swappable profiles. An upgrade for players who want to tune their controller to their games.AmazonSee at Amazon
Take better care of your PS5 controller: our toolbox
A few accessories to keep dust out, keep the controller charged and connect it properly.
- Anker 140 W braided USB-C to USB-C cable, 1.2 mCharges and syncs USB-C iPads and laptops. The braided sheath resists daily bending.AmazonSee at Amazon
- AABCOOLING Compressed Gas Duster Flex 750 ml, set of 3Blows dust out of the controller's USB-C port, button gaps and sticks, and a flexible tube reaches tight corners. A clean port gives the cable a better contact.AmazonSee at Amazon
- PowerA twin charging station for DualSense PS5 controllersCharges two DualSense controllers at the same time on its base, without using the console's USB ports. An LED shows the charge level and the controller lifts off with a click.AmazonSee at Amazon
- iFixit Moray precision screwdriver set (32 bits)This case holds 32 precision bits, including Phillips and Torx, to open the battery cover and other small devices. The hardened steel helps avoid damaging the screws.AmazonSee at Amazon
Frequently asked questions
How do I know if my PS5 controller is drifting?
Your controller is drifting if the character, camera or cursor moves on its own while you are not touching the stick. Note which stick is affected, left or right. Test it in a game with the stick at rest, after the reset described above.
Can you calibrate a PS5 controller?
Sony’s official pages mention no calibration tool and no dead zone setting in the console. Some games offer a dead zone setting in their controls options. It hides the drift in that game without repairing the stick.
Is PS5 controller drift covered by warranty?
On PlayStation Repairs, this problem falls under the “Button or analog stick issue” category. The Sony page we read says a repaired product is guaranteed for 3 months or until the end of the original warranty, if that is longer than 3 months, without stating the controller’s own warranty length. In the European Union, sellers generally owe a two-year legal guarantee, a point our sources do not confirm.
How do I reset a PS5 controller?
Turn off the PS5, unplug the controller, then press a pin into the small hole on the back, next to the Sony logo, for at least 5 seconds. Then connect the controller to the console with the official USB cable and press the PS button. Resetting erases no data.
Share this content:
