This article contains affiliate links: if you buy through them, Wanda-techs earns a commission at no extra cost to you.
Your dishwasher is not cleaning well: food stuck on, a gritty film, white spots on the glasses, or a top rack that comes out dirty. Bosch lists the usual causes as a clogged filter, spray arms that are blocked or have clogged nozzles, poor loading, a detergent tablet that did not dissolve, or the wrong cycle.
Start with the filter, then the spray arms.
Common symptoms and causes
- Food residue or a gritty film on the dishes: clogged filter, blocked arms or nozzles, tablet that did not dissolve.
- Baked-on white spots, cloudy glasses: water that is too hard (loaded with limescale) or a water softener that is set wrong. The softener is the module that removes limescale from the water using a resin and dishwasher salt.
- White haze on the surface: too much detergent, or salt deposits in the tub.
- Top rack not clean: spray arm blocked by the dishes, or clogged nozzles.
- Tea, coffee or lipstick stains: cycle too short or too cold.
- Scratches and marks: water too hot or products too harsh.
Good to know: a mark etched into glass does not come off. Fixing the cause only protects your dishes in the cycles that follow.
Before you start
- Keep your model’s manual within reach: the setting for water hardness, salt and rinse aid varies from one model to another.
- Get gloves, a toothpick or tweezers, a soft brush and a water hardness test strip.
Warning: unplug the appliance before opening anything, and never work on a dishwasher that is plugged in, or touch the capacitors that some appliances keep charged after unplugging. To replace a spray arm, unplug the dishwasher and shut off the water supply. Do not take apart the pump or the heating element: those parts are a job for a technician.
Warning: opening the appliance may void the warranty, so check the warranty end date first. Dishwasher salt is corrosive to metal: pour it only with the funnel supplied. A wrong water hardness setting can damage the softener resin.
Solution 1: clean the dishwasher filter
The filter catches food waste at the bottom of the tub. When it is clogged, less water reaches the spray arms.
- Put on gloves.
- Remove the lower rack.
- Release the filter unit at the bottom of the tub, then lift it out.
- Unscrew or separate the cylindrical filter from the rest of the unit.
- Rinse both parts under running water.
- Brush them gently, with no abrasive product.
- Put the filter back together and set it in place at the bottom of the tub.
- Turn it until the two arrows line up.

The filter is locked when the two arrows face each other. Then put the lower rack back.
Tip: scrape large food scraps into the trash before loading the plates. There is no need to pre-rinse them under the tap, though.
Good to know: Bosch gives no filter cleaning frequency in its help pages. Your model’s manual does. If water stands at the bottom of the tub, read our guide on a dishwasher that will not drain.
Solution 2: load the dishes properly
A plate or dish in the wrong spot blocks a spray arm or covers the detergent dispenser.
- Place cups and glasses in the top rack, spaced apart, tilted and not touching each other.
- Put tall stemmed glasses on the glass holder of the bottom rack.
- Put heavily soiled pots and pans in the bottom rack.
- Stand platters and cutting boards at the side, where they do not stop the arms from turning.
- Put plastic items in the top rack and secure the smallest ones with clips.
- Mix the cutlery in the cutlery basket, unless your appliance has a cutlery drawer.
- Place knives with the point facing down.
- Do not put anything over the tablet compartment: an object blocks the dispenser flap.
- At the end of the cycle, look at the compartment: a tablet still there did not dissolve.
The detergent compartment should be empty at the end of a cycle, and the arms should turn without touching the dishes. Bosch advises washing wooden boards by hand.
Tip: before closing the door, spin each arm one full turn by hand. A pot handle that catches is easy to spot.
Solution 3: unclog a blocked spray arm
Spray arms are the perforated rotating arms that throw water onto the dishes. They need to spin freely with clear nozzles. The nozzles are the small holes in the arms.
- Remove the lower rack.
- Spin each arm by hand to check that it turns freely.
- Take out the lower arm by pulling it upward.
- Release the upper arm: depending on the model, unscrew its nut or turn its clip, then pull it downward.
- Clear each nozzle with a toothpick or tweezers, on both sides of the arm.
- Rinse the arms under hot running water.
- Check that no debris is left inside, then let them drain.
- Snap the lower arm back on until it clicks.
- Insert the upper arm, then screw it on or turn the clip to lock it.
- Put the racks back in, pushing them in all the way.
- Run a short cycle to test.
The arms turn smoothly. The dishes in the top rack come out clean.
Warning: if the nozzles are clear and the arms still do not turn, Bosch recommends having the pump checked by a technician. To replace a damaged arm, unplug the appliance, shut off the water supply and wear gloves.
Solution 4: white spots, set the water hardness, salt and rinse aid
According to Bosch, water that is too hard is the main cause of white spots on glasses. Hardness measures the limescale content of the water. The scale below uses French degrees (°f), with the equivalent in ppm of calcium carbonate, which is what many US test strips show:
- 0 to 8 °f (0 to 80 ppm): very soft water;
- 8 to 15 °f (80 to 150 ppm): soft water;
- 15 to 30 °f (150 to 300 ppm): moderately hard water;
- more than 30 °f (over 300 ppm): very hard water.
- Let the tap water run for about 1 minute.
- Fill a glass and dip the test strip in it for about 1 minute.
- Read the result following the strip’s instructions.
- Set the water hardness on the control panel, or in the appliance menu on some models, following the manual.
- If your manual calls for it (see the question about all-in-one tablets), pour dishwasher salt into the salt reservoir at the bottom of the tub, using the funnel supplied.
- Wipe up any salt that spilled into the tub.
- Fill the rinse aid reservoir, located next to the detergent compartment.
To measure the hardness at home, here are test strips that read in degrees.

COMAP S900671 water hardness (TH) test strips
Measures tap water hardness by dipping a strip, with the result in French degrees. The reading helps set the water softener of a dishwasher or other appliance.
- AmazonSee at Amazon

On the next cycle, the glasses come out without new white spots. No test strip at hand? Your water utility can tell you the hardness of your water.
Good to know: above 20 °f (about 200 ppm), Bosch strongly recommends salt. A white haze on the surface points instead to too much detergent or salt deposits in the tub: reduce the detergent dose. If the dishes also come out wet, read our guide on a dishwasher that will not dry.
Solution 5: choose the right cycle and the right detergent
A cycle that is too short or too cold leaves tea or coffee stains.
- For stubborn or burnt-on soil, choose a high-temperature cycle, using your manual as a guide.
- If tea or coffee stains stay on the cups, avoid cycles that are too short or too cold.
- If the tablet stays in the compartment even though nothing blocks it, try a powder or a liquid detergent instead.
- If the dishes come out scratched or marked, switch to a cooler cycle and reduce the dose of product.
- Against limescale and grease in the tub, use a dishwasher cleaner or descaler, following the product’s instructions.
On the next cycle, the dishes come out with no stains or residue.
To deal with the limescale and grease in the tub, here is a liquid cleaner to run through an empty cycle.

Finish liquid dishwasher deep cleaner against limescale and grease, 250 ml
Descales and degreases the tub, spray arms and pipes during an empty cycle. Regular use prevents deposits and odours.
- AmazonSee at Amazon
If nothing works
Before another cycle, Bosch advises cleaning the filter, the drain pump, the spray arms and the door seals.
Does the problem persist after all these steps, or do the arms not turn despite clear nozzles? Stop there. Checking the circulation pump, which moves water through the arms, or the heating element, which heats the water, is a job for a technician.
For a Bosch, book a service visit online or call Bosch customer service. For another brand, contact the manufacturer’s service department. Have the appliance’s model number ready, found on its rating plate, along with a list of the fixes you have already tried.
Take better care of your dishwasher: our toolbox
These maintenance products help keep dishes clean and glasses free of marks.
- Finish dishwasher regenerating salt, 4 kgFeeds the dishwasher water softener to limit limescale in the tub. It helps prevent white marks on glasses when the water is hard.AmazonSee at Amazon
- Finish shine and drying rinse aid, 800 mlHelps water run off the dishes to limit drops and marks. Glasses dry better and come out shinier.AmazonSee at Amazon
- Finish liquid dishwasher deep cleaner against limescale and grease, 250 mlDescales and degreases the tub, spray arms and pipes during an empty cycle. Regular use prevents deposits and odours.AmazonSee at Amazon
- Wpro X12 descaler for washing machines and dishwashers (12 sachets)Descales the tub and circuit in an empty cycle. A monthly treatment helps prevent odours and protects the heating element.AmazonSee at Amazon
Frequently asked questions
Why is my dishwasher not cleaning well anymore?
A clogged filter, spray arms that are blocked or have clogged nozzles, poor loading, a tablet that did not dissolve, or the wrong cycle are the causes Bosch cites. Start with the filter and the arms, which you can check without tools. If you see white spots, check the water hardness and the salt.
How do I clean a dishwasher filter?
Take out the lower rack, release the filter unit at the bottom of the tub and separate the cylindrical filter. Rinse both parts under running water and brush them gently, with no abrasive. Reassemble the filter by turning it until the two arrows line up.
Why are there white spots on my dishes?
According to Bosch, water that is too hard is the main cause of white spots. Baked-on spots point to a softener that is set wrong, while a haze on the surface points more to too much detergent or salt deposits. Measure the water hardness, adjust the appliance to match, and check the salt and the rinse aid.
How do I unclog the spray arms?
Remove the arms, then run a toothpick or tweezers through each nozzle, on both sides. Rinse them under hot running water and check that no debris is left. Put them back and run a short cycle to check that they turn.
Do I need salt in a dishwasher with all-in-one tablets?
Advice differs, so follow your model’s manual. From the sources we read, one retailer recommends keeping salt and rinse aid, while a manufacturer’s manual says salt is unnecessary with all-in-one capsules. Bosch strongly recommends salt above 20 °f.
Share this content:
