This article contains affiliate links: if you buy through them, Wanda-techs earns a commission at no extra cost to you.
A robot lawn mower that won’t return to its charging station is most often held back by dirty charging contacts, a badly placed station or a damaged guide wire. It circles the station, stops just short of it or ends up with a flat battery in the middle of the lawn. Start with the contacts: it is the quickest check.
Common symptoms and causes
The mower circles its base without docking, stops near the station, can’t find its way back or doesn’t charge. Here are the causes to check:
- dirty charging contacts, or contacts that don’t touch the station’s properly;
- a station that sits crooked or has too little room around it;
- a guide wire or boundary wire that is cut, badly connected, or switched off in ECO mode;
- an obstacle, a stay-out zone or a passage that is too narrow on the way back;
- the wrong area mode, or the wrong setting for finding the station;
- a battery that is flat after winter or worn out;
- a damaged base plate antenna (flashing red light on Husqvarna).
Some behaviours are normal. On a wired Husqvarna Automower, a mower on its way home follows the guide wire without mowing.
On a lawn made of two unconnected parts, a Gardena can’t cross from one area to the other on its own. After you press the STOP button, an Automower has to be restarted on site: the app can’t relaunch it.
Before you start
The boundary wire is the cable laid on or under the ground that marks the mowing area. The guide wire links the station to that wire and shows the mower the way home. The menus below apply to wired Husqvarna Automower models controlled with the Automower Connect app.
Worx, Parkside, Bosch: the steps for the contacts, the station and the wire still apply. The menus and indicator lights of these brands have not been checked, so refer to your model’s manual.
Warning: stop the mower with the STOP button, switch off the main switch and wait until the blades have fully stopped before doing anything. Never lift the mower while the blades are spinning, and wear gloves.
Warning: unplug the station from the mains before touching its contacts or the wire, and never work on a live device. The capacitors in some appliances (TVs, microwaves, power supplies) stay charged after unplugging: don’t touch them.
Warning: never puncture, bend or heat a lithium battery. A swollen battery won’t charge any more and goes to a collection point. Work on a non-flammable surface.
Solution 1: clean the contacts when the mower won’t charge
The charging contacts are the metal strips through which the station feeds power to the mower.
- Remove leaves, cut grass and debris from the station’s docking area.
- Clean the station’s charging contacts.
- Clean the charging contacts under the mower.
- Plug the station back into the mains.
- Put the mower back in the station, pushing it in all the way.
- Check that the mower’s charging strips touch the station’s over their whole surface.

The mower stays in the station and starts charging again.
Tip: a dry cloth or a soft brush is enough for the contacts. After mowing wet grass, the green deposits come back quickly, so check them every time you clean the mower.
Solution 2: check the station’s position and level
A station that sits crooked is enough to make the mower back out.
- Place the station on a flat surface.
- Leave enough free space around the station.
- Check that the station’s cables are properly plugged in.
- On a Gardena, pick a spot from which the mower can leave and return in every direction.
- On a Gardena, avoid an area with heavy foot traffic.
The mower drives straight into the station, without bumping or backing out.
Solution 3: check the guide wire when the mower can’t find its base
On a Husqvarna Automower, the station’s light shows the state of the signal. With the station plugged back in, look at it before touching the wire.
- Look at the station’s light.
- If it flashes yellow, assume the guide wire is damaged (wired installations) and go to step 4.
- If it flashes red, stop: the base plate antenna may be damaged, and that is a job for an authorised service centre.
- Unplug the station, then check the guide wire’s connection to the station.
- Check the guide wire’s connection to the boundary wire.
- Follow the guide wire along its whole length, looking for a break.
- Reposition the wire or repair the break.
- Plug the station back in and check the light.
- If a manual start is blocked, switch off the mower’s ECO mode first.

The light stops flashing and the mower follows the guide wire to the station.
If you find a break, gel-filled waterproof connectors join the two ends of the wire and protect the joint from moisture.

ECENCE: 20 gel-filled waterproof connectors for robotic lawn mower boundary wire
Gel-filled connectors that join or repair a boundary wire and keep moisture out. Useful to protect cable ends left outdoors.
- AmazonSee at Amazon
Good to know: in ECO mode, the loop signal is switched off while the mower is parked. A light that is off or solid red has other meanings, which the Husqvarna page we used doesn’t detail: see the manual.
Tip: a break often hides where the wire may have been hit, near a spade cut, an edging or a pass of the string trimmer. Start with those spots.
Solution 4: clear the way back
A robot lawn mower that circles its base or stops short of it often gets stuck on the route itself.
- Remove anything blocking the route to the station.
- On a Husqvarna with AIM technology, open the app and delete or shrink the stay-out zones that cover the approach to the station.
- On a Gardena, measure the narrow passages: you need at least 60 cm (about 24 in) between the cables, plus a margin for obstacles.
- On a wire-free EPOS model, check that the station isn’t in an area with a weak satellite signal.
The mower gets through the passages and reaches the station without stopping.
Warning: on an EPOS model, a weak satellite signal stops the mower from finding its station, even with a clear route.
Solution 5: check the return settings and the area mode
One last check: the settings.
- On a wired Husqvarna Automower, open the Automower Connect app.
- Open Menu > Settings > Installation > Find charging station.
- Check the settings for finding the station.
- If the mower is in Secondary area mode, switch it to Main area mode.
- After mowing a secondary area, carry the mower by hand to the main area.
- Select the area mode that matches where the mower is.
The mower heads back to the station at the end of the cycle.
Good to know: on a Gardena with a lawn made of two unconnected areas, run a cable to the secondary area. In manual mode, it is up to you to bring the mower back to the station.
The support pages we used give no steps for a software update. Follow your mower’s app or manual.
If nothing works
If the battery was left flat over winter, it may be too weak to start charging again. Bring the mower indoors, put it on the station and leave it for several hours. The battery also refuses to charge outside a certain temperature range, which the page we used doesn’t specify.
Contact a Husqvarna dealer or authorised service centre, or your brand’s customer service, in these cases:
- flashing red light on the station (base plate antenna);
- a worn-out battery that no longer holds a charge;
- a wire break you can’t find despite a full check.
The same problem exists with indoor robots: see our guide Roomba won’t charge on its base any more. For a regular mower, see the checks for a mower that won’t start.
Take better care of your robot lawn mower: our toolbox
A few useful accessories to keep the boundary wire in good condition.
- ECENCE: 20 gel-filled waterproof connectors for robotic lawn mower boundary wireGel-filled connectors that join or repair a boundary wire and keep moisture out. Useful to protect cable ends left outdoors.AmazonSee at Amazon
Frequently asked questions
Why does my robot lawn mower circle its base without docking?
First check what keeps it from going fully into the station: debris on the docking area, dirty contacts or a station that isn’t level. The mower has to go in all the way for its strips to touch the station’s. Also check the free space around the station.
How does a robot lawn mower find its base?
On a wired Husqvarna Automower, it follows the guide wire to the station, without mowing on the way. Wire-free EPOS models locate themselves by satellite, and a weak signal stops them from finding the station. On a Gardena, the mower can’t cross from one lawn area to another on its own unless a cable links them.
How can I tell if the boundary wire is cut?
On a Husqvarna station, a flashing yellow light points to a damaged guide wire. Then follow the wire and check its connections to the station and to the boundary wire. A break can be repaired, after which the light should stop flashing.
Should I bring my robot lawn mower indoors for winter?
The pages we used don’t cover winter storage itself, but they flag a spring trap: a battery left flat all winter may be too weak to start charging again. If so, bring the mower indoors, put it on the station and let it charge for several hours. Check your model’s manual for winter storage instructions.
Share this content:
